Yokogawa DA100 Manuel d'utilisateur Page 74
- Page / 105
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-11E
7-9
Output Format
7
7.9 Report Output Format
Hourly report
The hourly report is output in the following format with the command, TS4+device
trigger(GET)+RF0.
Data
length
Year Month
Day Hour
Minute
0
A1
B1
C1 D1
An Bn Cn Dn
Number of output bytes
Time when the report is created
First channel
Last channel
A1 to An: Report channel number ( 00H to 3BH)
B1 to Bn: Unit number (Fixed to 80H during computation)
C1 to Cn: Channel number*
D1 to Dn: Report computation type
*: Computation channels are
00H to 1DH for stand-alone type
00H to 3BH for extended type
0
Extension
number
Power failure data 0: no failure 1:failure occurred
0 or 1
A1
An
A1
An
A1
An
E1 F1 G1
DATA H1
En Fn Gn
DATA Hn
E1 F1 I1
DATA J1
DATA Jn
E1 F1 K1
DATA L1
DATA Ln
En Fn In
En Fn Kn
Report computation data for each report channel
A1 ot An: Report channel number : 00H to 3BH
E1 to En:
Type of the report computation result to output
F1 to Fn: Report computation data status
G1 to Gn, l1 to ln, K1 to Kn:
Mantissa of the report computation data
Data H1 to data Hn:
Mantissa of the report computation data
Data J1 to data Jn:
Mantissa of the report computation data
Data L1 to data Ln:
Mantissa of the report computation data
Starting date and time of the sum for TOTAL
Instantaneous value, average value
or summed value
Minimum value or Total of
the summed values
Maximum value
Year Month
Day Hour
Minute
Note
• RF0 outputs data on the specified report channles.
Data length
The number of output bytes can be determined from the following expression.
Number of output bytes = 16 + 4 x N + 8 x N x 3 + (8 + 8 + N) x extension number
N: Number of output channels
Report computation type
Output the type of computation set for each report channel.
00H: OFF
01H: INST (Instantaneous value)
02H: AVE (Average)
03H: SUM (Sum)
The type of report computation result to output
The report computation results vary depending on the report computation types. The following
types of report computation results are output.
Output value Type of report computation result to output Report computation type
00H Invalid data OFF
01H INST (instantaneous value) INST
02H AVE (average value) AVE
03H SUM (summed value) SUM
04H MIN (minimum value) AVE
05H MAX (maximum value) AVE
06H TOTAL (total of the summed values) SUM
- Instruction 1
- Data Acquisition Unit 1
- Communication Interface 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 5
- CHAPTER 8 SAMPLE PROGRAM 5
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- Host Computer 14
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- 4.5 Connection Methods 36
- DA100's IP address 41
- <Enter> 41
- 4.9 Setting the Timeout 42
- 5.1 Command Format 43
- 5.2 Command Syntax 45
- Channel/relay No 46
- 5.4 Command List 47
- 5.5 Input Range Parameter 48
- RATE RATE 0 to 30000 50
- GATE GATE 0 to 30000 50
- Command Format 51
- 5.5 Input Range Parameter 51
- 5.6 ASCII Code Table 52
- 6.1 Setting Command 53
- 6.1 Setting Command 54
- Setting the strain input 54
- Setting the pulse input 54
- Setting Scaling 54
- SN Sets the scaling unit 55
- SA Sets the alarm 55
- SL Sets an event/action 57
- Commands 59
- XT Sets the temperature unit 61
- 6.2 Control Execution 62
- 6.3 Data Output 64
- Request Command 64
- 7.1 Functions as Talker 66
- Expandable model: A01 to A60 67
- Position 71
- 7.9 Report Output Format 74
- Daily Report 76
- 7.9 Report Output Format 77
- Monthly Report 78
- 8.1 GP-IB Sample Programs 82
- 8.2 RS-232-C Sample Programs 85
- Output the Setting Data 88
- Sample Program 90
- 8.4 Ethernet Program 94
- App.1 Computing Equation 96
- Computation start 98
- Computation stop 98
- Computation clear & start 98
- Computed data 98
- Measurement interval 99
- Computation 99
- App. 2 Report Function 100
- IM DA100-11E 101
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa DA100 Manuel d'utilisateur
(109 pages)
(109 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.396 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels