Yokogawa DA100 Manuel d'utilisateur Page 41
- Page / 105
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4-12
IM DA100-11E
7. Enter any of the following commands to display the various information.
wlog: Warning information
con: Connection information
net: Network information
quit: Terminate the information display and disconnect the connection
If you are using UNIX, follow the directions below.
1.
Port
DA100's IP address
telnet 133.140.1.1 34159
<Enter>
or
Port
DA100's IP address
telnet
open 133.140.1.1 34159
<Enter>
<Enter>
2. Enter any of the following commands: wlog, con, or net.
The following information is displayed.
Warning indication
Command
Number of warning occurrences
Most recent warning number
Eight most recent warning codes
wlog
warning Log
total : 3
current : 3
code : 1:200 2:100 3:300 4:0 5:0 6:0 7:0 8:0
END
1 : Internal buffer is overflowed
2 : 16 collision occurred
3 : Part of EEPROM is invalid
Warning codes
Connection information
con
Active connections
Proto Local Address Foreign Address State
TCP 133. 140. 104. 2:34150 133. 140. 104. 1:1026 ESTABLISHED
TCP 133. 140. 104. 2:34159 133. 140. 104. 1:1024 ESTABLISHED
TCP 0. 0. 0. 0:34159 0. 0. 0. 0:34159 LISTEN
TCP 0. 0. 0. 0:34151 0. 0. 0. 0:34151 LISTEN
TCP 0. 0. 0. 0:34150 0. 0. 0. 0:34150 LISTEN
END
Command
Socket address of the connection destination
Displayed as "IP address: port address"
Socket address of the DA100
Displayed as "IP address: port address"
Protocol in use (supports only TCP)
Connection State
ESTABLISHED: Connection established
Network information
net
Network Status
APP: timeout = 15min
APP:34150 timeout = 1
APP:34151 timeout = 1
TCP:keep alive = 1
TCP:connects = 5
TCP:closed = 5
TCP:timeoutdrops = 0
TCP:keepdrops = 0
TCP:sndtotal = 121
TCP:sndbyte = 8552
TCP:sndrexmitpack = 1
TCP:sndrexmitbyte = 209
TCP:rcvtotal = 150
TCP:rcvbyte = 128
DLC:16 collisons = 0
Command
Total number of disconnection on port 34150 due to timeouts
Total number of disconnection on port 34151 due to timeouts
Keep alive chack sycle
Total number of times the connection has been established
Total number of times the connection has been disconnected
Total number of times the connection has been disconnected due to TCP retransmission *
1
Total number of times the connection has been disconnected due to TCP Keepalive timeouts
Total number of packets *
2
transmitted
Total number of bytes transmitted
Total number of packets retransmitted
Total number of bytes retransmitted
Total number of packets received
Total number of bytes received
Number of times 16 collision*
3
occurred
*1: If the sent packet is not received, the packet is automatically retransmitted at a predetermined time interval. If the
packet is not received after retransmitting 14 times from the DA100, the connection is disconnected as a timeout.
*2: The unit (size) by which data are transmitted.
*3: Collisions occur when packets collide on the network. Collisions occur more frequently when the network is
congested. The condition in which collisions occur 16 times in succession is called 16 collision.
Timeout setting (ET command)
4.8 Displaying the Communication Information
- Instruction 1
- Data Acquisition Unit 1
- Communication Interface 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 5
- CHAPTER 8 SAMPLE PROGRAM 5
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- Host Computer 14
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- 4.5 Connection Methods 36
- DA100's IP address 41
- <Enter> 41
- 4.9 Setting the Timeout 42
- 5.1 Command Format 43
- 5.2 Command Syntax 45
- Channel/relay No 46
- 5.4 Command List 47
- 5.5 Input Range Parameter 48
- RATE RATE 0 to 30000 50
- GATE GATE 0 to 30000 50
- Command Format 51
- 5.5 Input Range Parameter 51
- 5.6 ASCII Code Table 52
- 6.1 Setting Command 53
- 6.1 Setting Command 54
- Setting the strain input 54
- Setting the pulse input 54
- Setting Scaling 54
- SN Sets the scaling unit 55
- SA Sets the alarm 55
- SL Sets an event/action 57
- Commands 59
- XT Sets the temperature unit 61
- 6.2 Control Execution 62
- 6.3 Data Output 64
- Request Command 64
- 7.1 Functions as Talker 66
- Expandable model: A01 to A60 67
- Position 71
- 7.9 Report Output Format 74
- Daily Report 76
- 7.9 Report Output Format 77
- Monthly Report 78
- 8.1 GP-IB Sample Programs 82
- 8.2 RS-232-C Sample Programs 85
- Output the Setting Data 88
- Sample Program 90
- 8.4 Ethernet Program 94
- App.1 Computing Equation 96
- Computation start 98
- Computation stop 98
- Computation clear & start 98
- Computed data 98
- Measurement interval 99
- Computation 99
- App. 2 Report Function 100
- IM DA100-11E 101
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa DA100 Manuel d'utilisateur
(109 pages)
(109 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.522 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels