Yokogawa DA100 Manuel d'utilisateur télécharger pdf (Page 59)

IM DA100-11E

6-7

Commands

Integration time: Equivalent to 50/60 Hz

Input module Filter off Filter on

10CH 0.5* 3

20CH 2 4

30CH 2 4

*: 2s if the power monitor module is installed

Integration time: 100 ms

Input module Filter off Filter on

10CH 4 12

20CH 5 15

30CH 6 20

XI Sets the A/D integration time.

Mode Setup mode

Setting XIp1, p2<terminator>

p1 Subunit (0 to 5)

p2 Integration time (AUTO, 50 Hz, 60 Hz,

100 ms)

Example Set the A/D integration time in subunit 0 to 50

Hz.

XI0, 50Hz

XQ Sets the filter.

Mode Setup mode

Setting XQp1<terminator>

p1 ON Filter on

OFF Filter off

Example Insert a filter in the input.

XQON

XA Performs the setting related to alarm.

Mode Setup mode

Setting XAp1, p2, p3<terminator>

p1 Interval for limit of increasing rate-of-

change (1 to 15)

p2 Interval for limit of decreasing rate-of-

change (1 to 15)

p3 Alarm hysteresis (0.0 to 1.0)

Example Set the interval for limit of increasing rate-of-

change to 10, the interval for the limit of the

decreasing rate-of-change to 10 and alarm

hysteresis to 0.5%.

Comments • This command sets an interval to detect the rate-

of-change alarm and hysteresis.

• Set an interval using the measurement period

as the unit.

• Set the hysteresis with the percentage of the

measurement range or scaling range.

• The computation channel hysteresis is fixed to

XY Sets the re-alarm for a re-failure.

Mode Setup mode

Setting XYp1, p2<terminator>

p1 Reflash number (1 to 6)

p2 Off, subunit (I, 0 to 5) + relay number

Example Set reflash relay 1 to relay module 1 connected to

slot 0 of the main unit.

XY1, I01

XN Sets AND/OR of the alarm output relay.

Mode Setup mode

Setting XNp1, p2<terminator>

p1 Unit

I: Main unit (DA100)

0 to 5: Subunit

p2 Relay number to be set to AND (01 to 60)

NONE: All are OR.

01-XX (XX=01 to 60)

Relays whose numbers are 1 to XX are

set to AND.

Example Have No. 1 of slot 0 to No. 10 of slot 2 in the

alarm output relay module connected to the main

unit be AND relay outputs.

XNI, I, 01-20

Comments • Setting is effective only in the same unit.

• Set p2 with the first relay number (01=fixed)

to the last relay number. If all OR output is to

be set, set p2 to NONE.

An error will occur when alarm output module or

DI/DO module isn’t mounted to selected DA100

or DS400/DS600.

XD Sets energizing or deenergizing.

Mode Setup mode

Setting XDp1, p2<terminator>

p1 Unit (I, 0 to 5) + Relay number (01 to 60)

p2 Selection of energizing/deenergizing

ENERG Energizing

DE-EN Deenergizing

Example Set the relays of No. 1 in slot 0 to No. 10 in slot 5

of the relay module connected to subunit 5 to

energizing outputs.

XD501-60, ENERG

Comments • If a successive number of output relays are to

be set, insert a minus sign (-) between the first

relay number and the last relay number, as

shown in the example. However, relays that

can be successively set are those in the same

subunit.

An error will occur when alarm output module or

DI/DO module isn’t mounted to selected DA100

or DS400/DS600.

XH Sets the hold/non-hold.

Mode Setup mode

Setting XHp1<terminator>

p1 Output relay hold on/off

ON Hold

OFF Non-hold

Example Hold the output state of an alarm output relay.

XHON

XB Sets the burnout.

Mode Setup mode

Setting XBp1, p2<terminator>

p1 Channel number (001 to 560)

p2 Selection of burnout

OFF

UP Upscale travelling beyond

the scale

DOWN Downscale travelling

beyond the scale

Example Set channels 01 to 10 of subunit 0 to upscale

burnout.

XB001-10, UP

Comments • If channels are to be set successively, the setting

is effective only when they are in the same unit.

6.1 Setting Command

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 104 105

Commentaires sur ces manuels

Pas de commentaire

Yokogawa DA100 Manuel d'utilisateur Page 59

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Yokogawa DA100