Yokogawa DA100 Manuel d'utilisateur Page 66
- Page / 105
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-11E
7-1
Output Format
7
7.1 Functions as Talker
There are the following thirteen types of data output:
• Measured data output (ASCII code): TS0 + “Device Trigger (GET)” + FM0
• Measured data output (binary code): TS0 + “Device Trigger (GET)” + FM1
• Computed data output (ASCII code): TS0 + “Device Trigger (GET)” + FM2
• Computed data output (binary code): TS0 + “Device Trigger (GET)” + FM3
• Setting of data output in the operation mode: TS1 + “Device Trigger (GET)” + LF
• Unit and decimal point position data output: TS2 + “Device Trigger (GET)” + LF
• System configuration data output: TS5 + “Device Trigger (GET)” + CF
• A/D calibration data output: TS8 + “Device Trigger (GET)” + LF
• Setting of data output in the setup mode: TS9 + “Device Trigger (GET)” + LF
• Output the hourly report using the report function: TS4+"GET"+RF0
• Output the daily report using the report function: TS3+"GET"+RF1
• Output the monthly report using the report function: TS3+"GET"+RF2
• Output the status of the hourly/daily/monthly report: TS3+"GET"+RF3
Measured/computed or report data output (TS0/TS3)
After executing the device trigger“GET ” be sure to output data using the FM command. Execution
of “GET” alone without executing the FM command does not output the data. After reading all the
data specified by the FM command, subsequent specification of the FM command without executing
“GET” enables the data within a scan to be output.
Setting data output (TS1, TS2, TS8 or TS9)
After transmitting the device trigger“GET ” be sure to output data using the LF command. Execution
of “GET” alone without executing the LF command does not output the data. After reading all the
data specified by the LF command, subsequent specification of another channel using the LF command
enables the data contents to be output. A/D calibration data output by the TS8 command can be
executed in the A/D calibration mode only.
Report output (TS4)
After transmitting the device trigger “GET ” be sure to read the data using the RF command. Execution
of “GET“ alone without executing the RF command does not read the data. After reading all the
specified data with the RF command, subsequent specification of another channel using the RF
command without executing “GET“ enables that data to be read.
System configuration output (TS5)
After transmitting the device trigger“GET,” be sure to output data using the CF command. Execution
of “GET” alone without executing the CF command does not output data.
Note
• Do not transmit the FM, LF, CF, or RF command before outputting data for specified channels.
• If an FM, LF, CF, or RF command is received while data are being transmitted, transmission of the data is suspended
automatically.
• If the type of output data is changed using the TS command after the execution of “GET,” the changed contents are not
reflected without executing “GET” again. Execute “GET” again.
• After executing “GET,” the execution of “GET” again without outputting data using the FM, LF, CF, or RF command or
without completing the data output sets new data to the buffer. Be careful because old data are lost.
- Instruction 1
- Data Acquisition Unit 1
- Communication Interface 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 5
- CHAPTER 8 SAMPLE PROGRAM 5
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- Host Computer 14
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- 4.5 Connection Methods 36
- DA100's IP address 41
- <Enter> 41
- 4.9 Setting the Timeout 42
- 5.1 Command Format 43
- 5.2 Command Syntax 45
- Channel/relay No 46
- 5.4 Command List 47
- 5.5 Input Range Parameter 48
- RATE RATE 0 to 30000 50
- GATE GATE 0 to 30000 50
- Command Format 51
- 5.5 Input Range Parameter 51
- 5.6 ASCII Code Table 52
- 6.1 Setting Command 53
- 6.1 Setting Command 54
- Setting the strain input 54
- Setting the pulse input 54
- Setting Scaling 54
- SN Sets the scaling unit 55
- SA Sets the alarm 55
- SL Sets an event/action 57
- Commands 59
- XT Sets the temperature unit 61
- 6.2 Control Execution 62
- 6.3 Data Output 64
- Request Command 64
- 7.1 Functions as Talker 66
- Expandable model: A01 to A60 67
- Position 71
- 7.9 Report Output Format 74
- Daily Report 76
- 7.9 Report Output Format 77
- Monthly Report 78
- 8.1 GP-IB Sample Programs 82
- 8.2 RS-232-C Sample Programs 85
- Output the Setting Data 88
- Sample Program 90
- 8.4 Ethernet Program 94
- App.1 Computing Equation 96
- Computation start 98
- Computation stop 98
- Computation clear & start 98
- Computed data 98
- Measurement interval 99
- Computation 99
- App. 2 Report Function 100
- IM DA100-11E 101
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa DA100 Manuel d'utilisateur
(109 pages)
(109 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.276 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels