Yokogawa DA100 Manuel d'utilisateur télécharger pdf (Page 65)

IM DA100-11E

6-13

Commands

• If the daily report is to be output using extended

format, the extended information must be

output within 1 hour from the creation of the

report. If the monthly report is to be output

using extended format, the extended

information must be output within 1 day from

the creation of the report. After that, the

extended information can not be output.

• If there is no valid data within the specified

report channel range, "FFFFH" is output.

LF Specifies the output channels for

setting data output, unit, and decimal

point data.

Mode All modes

Setting LFp1, p2<terminator>

p1 First output channel (001 to 560)

First output computation channel (A01 to

A60)

p3 Last output channel (001 to 560)

Last output computation channel (A01 to

A60)

Comments • Be sure to specify data to be output with the TS

command and execute “GET” or “ESC T”

before transmitting the FM command.

• If there is no input channel recognized by the

DA100 among specified channels, a syntax

error occurs.

• For stand-alone models computaion channel

number is A01 to A30.

CF Specifies the system

configuration output format.

Mode All modes

Setting CFp1<terminator>

p1 0 Information on system-configured

module

1 Current status module information

(realtime information)

Comments • Be sure to specify data to be output with the TS

command and execute “GET” or “ESC T”

before transmitting the CF command.

VF Requests the output of the relay

condition.

Mode Operation mode

Setting VFp1<terminator>

p1 0 Current relay condition

Comments • Before sending the VF command, make sure

to specify the output data with the TS command

and execute “GET” or “ESC T.”

BO Specifies the order of byte output

(in binary output).

Mode Operation mode

Setting BOp1<terminator>

p1 0 Output from MSB (upper-digit byte)

1 Output from LSB (lower-digit byte)

IM Specifies the mask of a status byte.

Mode Operation mode

Setting IMp1<terminator>

p1 First numerical value of the items( or

combination of those value) shown below.

0 sets all causes of interrupt to off.

1 Interrupt occurs at the end of an A/D

conversion.

2 Interrupt occurs at the time of a syntax

error.

4 Interrupt occurs when internal timer is

being operated or the time for hourly,

daily and monthly reports arrives.

32 Interrupt generated when measurement

release is generated while computation

is in progress.

Comments • Masks the causes of interrupt in the status byte.

• When either of the phenomena effectively

specified with this command occurs, bit 7

(SRQ) of the status byte is set to “1” and causes

an interrupt to the controller.

• For detailed instructions on the status byte, see

page 2-2.

SM Sets the auxiliary mask of the status

byte.

Mode Operation mode

Setting SMp1<terminator>

p1 A figure determined by the following

calculation:

p1 = a + b + c + d + e + f + g

a=1 Interrupt occurs when timer No. 1

operates.

=0 No interrupt occurs.

b=2 Interrupt occurs when timer No. 2

operates.

=0 No interrupt occurs.

c=4 Interrupt occurs when timer No. 3

operates.

=0 No interrupt occurs.

d=8 Interrupt occurs when timer No. 4

operates.

=0 No interrupt occurs.

e=16 Interrupt occurs when timer No. 5

operates.

=0 No interrupt occurs.

f=32 Interrupt occurs when timer No. 6

operates.

=0 No interrupt occurs.

g=64 Interrupt occurs when the time for

hourly, daily and monthly reports

arrives.

=0 No interrupt occurs.

Comments • Sets the auxiliary mask of interrupt when the

timers described in the IM command operate.

• When any of the timers whose numbers are

specified with this command operates, an

interrupt due to the internal time operation

occurs.

6.3 Data Output Request Command

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 104 105

Commentaires sur ces manuels

Pas de commentaire

Yokogawa DA100 Manuel d'utilisateur Page 65

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Yokogawa DA100