Yokogawa DA100 Manuel d'utilisateur télécharger pdf (Page 63)

IM DA100-11E

6-11

Commands

• If initial balancing is executed, number-of-

channels worth of data are returned in the

following format.

S1 S2 CCC DDCrLf

S1: Data status 1

N: Normal

S: SKIP

S2: Data status 2

Space: Data in the middle

E: Data at the end

CCC: Channel number

DD: Result of the initial balancing

OK: Initial balancing succeeded

NG: Initial balancing failed

DF: Default values set

_: Skip module

DR Start/stop the report

Mode Operation mode

Setting DRp1<terminator>

p1 Start/stop the report

0: Start the report

1: Stop the report

Example Start the report.

DR0

Comments • Effective only on instruments with the optional

report function.

• Measurement range, date, time cannot be

changed during a report. Copy using the range

copy ON also cannot be executed during a

report.

• All report data up to that point are cleared when

a report is started.

• This setting is effective when one of hourly,

daily and monthly reports is ON.

RS Executes a system reconstruction.

Mode Operation mode

Setting RSp1<terminator>

p1 0, Reconstruct the system.

Example Reconstruct the system.

RS0

Comments • Reconstruct the system. Execute this command

if a subunit or a module is newly added or a

module in a slot is replaced.

• Since it takes an indefinite time to execute the

RS command, return an ACK after processing.

On the controller side, execute the following

processing after receiving the ACK after

transmitting the RS command. The ACK status

format is as shown below.

E0Cr+Lf: The received command has been

normally processed.

E1Cr+Lf: There is an error in the received

command.

• After executing the command, the clock is

initialized to 96/01/01 00:00:00.

RC Executes the initializing of set values.

Mode Operation mode

Setting RCp1<terminator>

p1 0, Initialize the set values.

Example Initialize the operation mode parameters

(measuring range, unit, alarm, date & time, and

moving average).

RC0

Comments • Since it takes an indefinite time to execute the

RC command, return an ACK after processing.

On the controller side, execute the following

processing after receiving the ACK after

transmitting the RC command. The ACK status

format is as shown below.

E0Cr+Lf: The received command has been

normally processed.

E1Cr+Lf: There is an error in the received

command.

• After executing the command, the clock is

initialized to 96/01/01 00:00:00.

DS Transfers the setting mode.

Mode All modes

Setting DSp1<terminator>

p1 0 Transferred to operation mode.

1 Transferred to setup mode.

2 Transferred to A/D calibration mode.

Example Transfer the DA100 mode to the setup mode.

DS1

Comments • Since it takes an indefinite time to execute the

DS command, return an ACK after processing.

On the controller side, execute the following

processing after receiving the ACK after

transmitting the DS command. The ACK status

format is as shown below.

E0Cr+Lf: The received command has been

normally processed.

E1Cr+Lf: There is an error in the received

command.

• After executing the command, the clock is

initialized to 96/01/01 00:00:00.

VD Turn ON/OFF the relays specified by the

VS command.

Mode Operation mode

Setting VDp1, p2, p3<terminator>

p1 First relay number of the module (I01 to

560, S01 to S60)

p2 Setting procedures

SET Set the relay corresponding to the

“1” bit specified by p3 to ON, and

the relay corresponding to the “0”

bit to OFF.

ON Set the relay corresponding to the

“1” bit specified by p3 to ON.

OFF Set the relay corresponding to the

“1” bit specified by p3 to OFF.

p3 Setting pattern for one module

Four four-bit values (total of 16 bits), each

displayed in hexadecimal notation.

216

0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 1

F830

Bit No.

345678

91011

12131415

First relay

The value of p3

Last relay

Setting pattern

Example Turn ON relay 11 to 15 and maintain 16 to 20 at

the current condition of sub unit 1.

VD111, ON, 001F

Comments • Because the settings are done on a module basis,

set p1 to the first relay number of the module.

• If p2 is set to ON, the relays with the setting

parameters of 1 are turned ON, and those of 0

maintain the current condition.

6.2 Control Execution Command

1 2 ... 58 59 60 61 62 63 64 65 66 67 68 ... 104 105

Commentaires sur ces manuels

Pas de commentaire

Yokogawa DA100 Manuel d'utilisateur Page 63

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Yokogawa DA100