Yokogawa DA100 Manuel d'utilisateur Page 69
- Page / 105
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-11E
7-4
7.4 Setting Data Output Format (Operation mode)
The operation mode parameters are output in the following order by the TS1 + “Device Trigger
(GET)” + LF command:
SR
Measured range setting data for the first channel
SR Measured range setting data for the last channel
SN
Unit setting data for the first channel
Unit setting data for the last channel
SN
SA
SA
SV
SV
EN
Alarm setting data for the first channel
Alarm setting data for the last channel
Moving average setting data for the last channel
Moving average setting data for the first channel
Output completed.
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
SO
Computation expression setting data for the first computation channel
SO Computation expression setting data for the last computation channel
CrLf
CrLf
SI
Setting data for No. 1 timer
SI Setting data for No. 6 timer
CrLf
CrLf
SQ
Setting data for No. 1 match time
SQ Setting data for No. 3 match time
CrLf
CrLf
SL
Setting data for No. 1 event action
SL Setting data for No. 30 event action
CrLf
CrLf
SX
Setting data for No. 1 group
SX Setting data for No. 7 group
CrLf
CrLf
SK
Constant setting data for the first constant number
SK Constant setting data for the last constant number
CrLf
CrLf
Setting data for the channels in the range specified by the LF command are output for every subunit.
Channel numbers are output in the order of input channels and computation channels. For example,
when LF005 , A10 is set, the data are output starting from the input channel 005 to the last input
channel. Then, the data are output starting from computation channels A01 to A10.
Data are output in the order of setting parameters subsequent to the setting command. Each data
item is delimited with a comma (,).
Alarm setting data
For alarm setting data, setting data from level 1 to level 4 are output for every channel.
SA
Level 1 alarm setting data
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
CrLf
Level 4 alarm setting data
Level 3 alarm setting data
Level 2 alarm setting data
CrLf
Level 1 alarm setting data
CrLf
CrLf
CrLf
Level 4 alarm setting data
Level 3 alarm setting data
Level 2 alarm setting data
CrLf
SA
SA
First channel
Second channel
Last channel
Level 1 alarm setting data
Level 4 alarm setting data
Level 3 alarm setting data
Level 2 alarm setting data
SA
SA
SA
- Instruction 1
- Data Acquisition Unit 1
- Communication Interface 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 5
- CHAPTER 8 SAMPLE PROGRAM 5
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- Host Computer 14
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- 4.5 Connection Methods 36
- DA100's IP address 41
- <Enter> 41
- 4.9 Setting the Timeout 42
- 5.1 Command Format 43
- 5.2 Command Syntax 45
- Channel/relay No 46
- 5.4 Command List 47
- 5.5 Input Range Parameter 48
- RATE RATE 0 to 30000 50
- GATE GATE 0 to 30000 50
- Command Format 51
- 5.5 Input Range Parameter 51
- 5.6 ASCII Code Table 52
- 6.1 Setting Command 53
- 6.1 Setting Command 54
- Setting the strain input 54
- Setting the pulse input 54
- Setting Scaling 54
- SN Sets the scaling unit 55
- SA Sets the alarm 55
- SL Sets an event/action 57
- Commands 59
- XT Sets the temperature unit 61
- 6.2 Control Execution 62
- 6.3 Data Output 64
- Request Command 64
- 7.1 Functions as Talker 66
- Expandable model: A01 to A60 67
- Position 71
- 7.9 Report Output Format 74
- Daily Report 76
- 7.9 Report Output Format 77
- Monthly Report 78
- 8.1 GP-IB Sample Programs 82
- 8.2 RS-232-C Sample Programs 85
- Output the Setting Data 88
- Sample Program 90
- 8.4 Ethernet Program 94
- App.1 Computing Equation 96
- Computation start 98
- Computation stop 98
- Computation clear & start 98
- Computed data 98
- Measurement interval 99
- Computation 99
- App. 2 Report Function 100
- IM DA100-11E 101
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa DA100 Manuel d'utilisateur
(109 pages)
(109 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.979 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels