Yokogawa DA100 Manuel d'utilisateur télécharger pdf (Page 54)

IM DA100-11E

6-2

6.1 Setting Command

Setting the strain input

Setting SRp1, p2, p3, p4, p5<terminator>

p1 Channel number (001 to 560)

p2 STRAIN

p3 Measurement range

2k/20k/200k

p4 Left value of span

p5 Right value of span

Example Set the measurement range of subunit 1 and

channel 01 to 20k, left value of span to 0, and

right value of span to 100.

SR101, STRAIN, 20k, 0, 100

Comments • Even when the settings of p3 are the same

parameters, the measurement range of the strain

varies depending on the gauge method. For

details, refer to page 5-7.

• Set spans, p4 and p5, within the measurement

range indicated in page 5-7.

• Input values within 6 digits disregarding the

decimal point for p4 and p5.

• The measurement range cannot be changed

while executing a report or computation.

Setting the pulse input

Setting SRp1, p2, p3, p4, p5, p6, p7, p8, p9<terminator>

p1 Channel number (001 to 560)

p2 PULSE

p3 Measuring mode

RATE momentary pulse count mode

GATE contact ON/OFF detection mode

p4 Left value of span (0 to 30000)

p5 Right value of span (0 to 30000)

p6 Left value of scale (0 to 30000)

p7 Right value of scale (0 to 30000)

p8 Decimal point position of scale (0 to 4)

p9 Filter (ON or OFF)

Example Set subunit 1 and channel 01 to momentary pulse

count mode, left value of span to 0, and right value

of span to 1000.

SR101, PULSE, RATE, 0, 1000, 0, 1000, 0

Comments • When omitting p6, p7, or p8, omit all three.

• When summing the count number or the ON

time, set the computational expression with the

SO command, then execute computation start

with the EX command. When the pulse input

module is installed, the use of computation

channels become available without the math

option. However, the only computational

expression available in this case is

TLOG.PSUM(XXX) for summing the count

number or the ON time.

• The measurement range cannot be changed

while executing a report or computation.

Setting Scaling

Setting SRp1, p2, p3, p4, p5, p6, p7, p8, p9<terminator>

p1 Channel number (001 to 560)

p2 SCL

p3 Type of input

VOLT DC voltage

TC Thermocouple

RTD Resistance temperature detector

DI Contact

p4 Measurement range

p5 Left value of span

p6 Right value of span

p7 Left value of scale (-30000 to 30000)

p8 Right value of scale (-30000 to 30000)

p9 Decimal point position of scale (0 to 4)

Example Change channel 02 of subunit 0 to an input in

which 1 V is converted to 0.00 and 5 V to 100.00.

SR002, SCL, VOLT, 6V, 1000, 5000, 0, 10000,

Comments • For the p4 measurement range, see the range

parameter table on Pages 5-6 and 5-7.

• For the p5 and p6 setting spans, set them in the

ranges shown in the setting range on Pages 5-6

and 5-7.

• For p5 and p6 setting values, enter them within

6 digits excluding the decimal point.

• Select either to set all three parameters, p7, p8

and p9, or to omit them all.

• The measurement range cannot be changed

while executing a report or computation.

Setting the power monitor scaling

Setting SRp1, p2, p3, p4, p5,...., p11<terminator>

p1 Channel number (001 to 560)

p2 SCL

p3 AC

p4 Wiring method

1Ph2W: Single-phase two-wire system

1Ph3W: Single-phase three-wire system

(only on a three-wire system)

3Ph3W-2I: Three-phase three-wire system

(only on a two-voltage two-

current three-wire system)

3Ph3W-3I: Three-phase three-wire system

(only on a three-voltage three-

current three-wire system)

3Ph4W: three-phase four-wire system

(only on a three-wire system)

p5 Input range

25 V - 0.5 A

25 V - 5 A

250 V - 0.5 A

250 V - 5 A

p6 Measurement item

p7 Left value of span

p8 Right value of span

p9 Left value of scale (-30000 to 30000)

p10 Right value of scale (-30000 to 30000)

p11 Decimal point position of scale (0 to 4)

Example Measure the active power on subunit 0 and channel

01, and convert 10W to 0.00 and 100W to 100.00.

SR001, SCL, AC, 3Ph3W-2I, 250V-0.5A,

P1, 10, 100, 000, 10000, 2

Comments • Settings of p4 and p5 are common within one

power monitor module. If the setting is

changed, the settings on other channels also

change.

• For the measurement item p6, refer to the list

of measurement items on page 5-9.

• There are items that can not be set on the

measurement item, p6, depending on the wiring

method or the settings on other channels. Set

within the group indicated on page 5-9.

• Set the span values, p7 and p8, within the

measurement range indicated on page 5-7.

• Input values within 6 digits disregarding the

decimal point for p7 and p8. The decimal point

position is fixed to the decimal point position

of the setting range of page 5-7.

• For p9, p10, and p11, either set all the three

parameters or omit all three.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 104 105

Commentaires sur ces manuels

Pas de commentaire

Yokogawa DA100 Manuel d'utilisateur Page 54

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Yokogawa DA100