Yokogawa DA100 Manuel d'utilisateur Page 81
- Page / 105
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-11E
7-16
7.10 Relay Condition Output Format (Operation mode)
The command TS0 + device trigger (Get) + VF0 results in a Relay condition output in below format:
Data length
123456
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
ON/OFF condition
ON/OFF condition ON/OFF condition ON/OFF condition
ON/OFF condition ON/OFF condition
Data length
Slot 0
Slot 1 Slot 2 Slot 3 Slot 4 Slot 5
Main unit
Internal switch
Internal switch
Main unit
Sub unit 0
Sub unit 1
Sub unit 2
Sub unit 3
Sub unit 4
Sub unit 5
Stand-alone model
Expandable model
WORD
1
234
5678
9
10
10001
1
111
0
Relay number
Relay condition
1: ON
0: OFF
Not used
Details of ON/OFF condition
MSB
LSB
For output from the upper byte
123
45
6
7
8
910
1
000
1
111
1
0
Not used
MSB LSB
For output from the lower byte
Relay conditions of internal switch, DI/DO module and alarm module are output.
0 is the output for all modules except for the DI/DO and alarm module.
Note
• All data will be output in hexadecimal notation.
• According to the output order specified with the BO command, the data of relay ON/OFF condition can be output from
MSB (upper byte) or LSB (lower byte).
• The initial value for BO command is MSB.
• If no DI/DO nor alarm modules are connected to the DA100, output for relay conditions of the whole system will be 0.
- Instruction 1
- Data Acquisition Unit 1
- Communication Interface 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 5
- CHAPTER 8 SAMPLE PROGRAM 5
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- Host Computer 14
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- 4.5 Connection Methods 36
- DA100's IP address 41
- <Enter> 41
- 4.9 Setting the Timeout 42
- 5.1 Command Format 43
- 5.2 Command Syntax 45
- Channel/relay No 46
- 5.4 Command List 47
- 5.5 Input Range Parameter 48
- RATE RATE 0 to 30000 50
- GATE GATE 0 to 30000 50
- Command Format 51
- 5.5 Input Range Parameter 51
- 5.6 ASCII Code Table 52
- 6.1 Setting Command 53
- 6.1 Setting Command 54
- Setting the strain input 54
- Setting the pulse input 54
- Setting Scaling 54
- SN Sets the scaling unit 55
- SA Sets the alarm 55
- SL Sets an event/action 57
- Commands 59
- XT Sets the temperature unit 61
- 6.2 Control Execution 62
- 6.3 Data Output 64
- Request Command 64
- 7.1 Functions as Talker 66
- Expandable model: A01 to A60 67
- Position 71
- 7.9 Report Output Format 74
- Daily Report 76
- 7.9 Report Output Format 77
- Monthly Report 78
- 8.1 GP-IB Sample Programs 82
- 8.2 RS-232-C Sample Programs 85
- Output the Setting Data 88
- Sample Program 90
- 8.4 Ethernet Program 94
- App.1 Computing Equation 96
- Computation start 98
- Computation stop 98
- Computation clear & start 98
- Computed data 98
- Measurement interval 99
- Computation 99
- App. 2 Report Function 100
- IM DA100-11E 101
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa DA100 Manuel d'utilisateur
(109 pages)
(109 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.501 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels