Yokogawa Integral Oxygen Analyzer ZR202 Manuel d'utilisateur Page 52
- Page / 157
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
<4. Piping>
4-3
IM 11M12A01-04E
4.2 Piping for System 2
Piping in System 2 is illustrated in Figure 4.7.
~
ZR202G Integrated type Zirconia Oxygen Analyzer
F1.2E.ai
ZA8F flow setting unit
Reference gas
Calibration gas
Needle
valve
Flowmeter
Instrument air
Air Set
Pressure
regulator
Zero gas cylinder
Calibration gas unit case
Stop valve
or
Check valve
Span gas(Same as Zero gas calibration)
100 to 240 V AC
Contact input
Analog output, contact output
Digital output (HART)
Figure 4.7 Piping for System 2
System 2 illustrated in Figure 4.7 requires piping as follows:
• Mount the check valve or the stop valve through a nipple to the calibration gas inlet of the equipment.
4.2.1 Piping Parts for System 2
Check that the parts listed in Table 4.2 are provided.
Table 4.2 Piping Parts
Equipment Piping location Parts Name Description
Oxygen Analyzer Calibration gas inlet Stop valve or check valve Stop valve (L9852CB or G7016XH
recommended by YOKOGAWA
Check valve (K9292DN or K9292DS)
provided by YOKOGAWA
Nipple * Rc1/4 or 1/4 NPT General parts
Zero gas cylinder User' s scope
Pressure Regulator (G7013XF or G7014XF) recommended by
YOKOGAWA
Joint for tube connection Rc1/4 or 1/4 NPT General parts
Reference gas inlet Air set (G7003XF/ K9473XK or G7004XF
/ K9473XG) recommended by YOKOGAWA
Joint for tube connection Rc1/4 or 1/4 NPT General parts
Note: Parts with marking * are used when required.
General parts can be found on the local market.
4.2.2 Piping for the Calibration Gas
This piping is to be installed between the zero gas cylinder and the ZA8F ow setting unit, and
between the ZA8F ow setting unit and the ZR202G analyzer.
The cylinder should be placed in a case assembly E7044KF or the like to avoid any direct sunlight or
radiant heat so that the gas cylinder temperature may not exceed 40°C.
Mount the pressure regulator (recommended by YOKOGAWA) on the cylinder.
Mount the stop valve or the check valve (recommended by YOKOGAWA) through the nipple (found
on the local market) at the calibration gas inlet of the equipment as illustrated in Figure 4.8. (The stop
valve or the check valve may have been mounted on the equipment when shipped.) Connect the
ow setting unit and the analyzer to a 6mm (O.D.) x 4mm (I.D.) (or nominal size 1/4 inches) or larger
stainless steel pipe.
- Model ZR202G 1
- Integrated type 1
- Zirconia Oxygen Analyzer 1
- Introduction 2
- <Introduction> 3
- Relates to 3
- (1) About This Manual 4
- IMPORTANT 5
- NOTICE 7
- After-Sales Warranty 8
- CONTENTS 10
- <CONTENTS> 11
- 1. Overview 16
- 1.1.2 System 2 17
- 1.1.3 System 3 18
- 1.2.1 System Components 19
- 2. Specications 20
- <2. Specications> 21
- <2. Specications> 22
- Functions 23
- Display and setting content: 23
- Model and Codes 25
- • External Dimensions 26
- • Standard Accessories 26
- 2.1.3 ZO21R Probe Protector 28
- • Specications 31
- • Model and Codes 31
- External Dimensions 32
- 2.3 ZO21S Standard Gas Unit 33
- 2.4 Other Equipment 34
- • Standard Specication 35
- • Standard Specications 35
- Standard Specications 36
- F2.16.EPS 38
- Blank Page 39
- 3. Installation 40
- 3.1.2 Probe Insertion Hole 41
- Probe Protector (ZO21R) 42
- <3. Installation> 43
- 3.2.1 Installation Location 44
- 3.3.1 Installation Location 46
- Calibration Gas Cylinder 48
- 4. Piping 50
- Stop valve 51
- Tube connection 51
- 4.2 Piping for System 2 52
- 4.3 Piping for System 3 53
- <4. Piping> 54
- Compensation 55
- Table 4.3 Piping Parts 57
- 5. Wiring 58
- 5.1.2 Wiring 59
- 5.2 Wiring for Analog Output 60
- 5.3.1 Wiring for Power Line 61
- 5.5 Wiring for Contact Input 62
- 5.5.2 Wiring Procedure 63
- 6. Components 64
- 7. Startup 66
- 7.2 Valve Setup 67
- 7.4.1 Display and Switches 68
- 7.4.2 Display Conguration 69
- 7.4.5 Changing Set Values 71
- 7.7 Output Range Setting 74
- 7.8 Checking Current Loop 76
- 7.9 Checking Contact I/O 76
- 7.9.1 Contact Output Check 77
- 7.10 Calibration 80
- 7.10.2 Manual Calibration 82
- 8. Detailed Data Setting 84
- Concentration ( at 20 mA) 85
- 8.2.4 Default Values 85
- 8.3 Output Hold Setting 86
- Output hold time 87
- 8.3.3 Output Hold Setting 88
- 8.3.4 Default Values 88
- 8.4.1 Alarm Values 89
- 8.4.2 Alarm Output Actions 89
- 8.4.3 Alarm Setting 90
- 8.5 Output Contact Setup 91
- 8.5.3 Default Values 93
- 8.6 Input Contact Settings 94
- 8.7 Other Settings 95
- 8.7.3 Setting Fuels 97
- For liquid fuel 98
- For gas fuel 98
- For solid fuel 98
- Absolute 99
- Dry-bulb temperature, °C 99
- Table 8.16 Fuel Data 100
- 8.7.4 Setting Purging 101
- 9. Calibration 102
- 9.1.2 Calibration Gas 103
- 9.1.3 Compensation 103
- <9. Calibration> 104
- <9. Calibration> 105
- 9.2 Calibration Procedures 106
- IM 11M12A01-04E 108
- 9.2.2 Calibration 109
- 10. Other Functions 110
- 10.1.1 Air Ratio 112
- 10.1.2 Cell Temperature 112
- 10.1.3 C. J. Temperature 112
- 10.1.5 Cell Voltage 113
- 10.1.6 Thermocouple Voltage 113
- 10.1.7 Cold Junction Voltage 113
- 10.1.8 Current Output 113
- 10.1.9 Response Time 114
- 10.1.11 Robustness of a Cell 114
- <10. Other Functions> 115
- 00.06.21 116
- 10.4 Reset 118
- Table 10.6 Resetting 119
- 10.5.3 Calibration Gas Flow 126
- Setting Unit 128
- Calibration gas tube 131
- Exploded view of components 131
- (with outside diameter 131
- Groove in which the contact 132
- (E7042BS) is placed 132
- F11.2E.ai 132
- View A-A 134
- F11.4E.ai 134
- 11.1.5 Replacement of O-ring 135
- F11.5E.ai 137
- Cover of Display 137
- Calibration Unit 139
- 12. Troubleshooting 140
- <12. Troubleshooting> 141
- Generated 143
- Multimeter 146
- (Ω) 146
- Heater wire 146
- Customer 150
- Maintenance 150
- Parts List 150
- CMPL 11M12A01-04E 151
- Revision Information 156
Produits connexes et manuels pour Équipement aérien Yokogawa Integral Oxygen Analyzer ZR202
(24 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.983 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels