Yokogawa DA100 Manuel d'utilisateur Page 76
- Page / 109
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-01E
4-7
4
Specifications
Ambient temperature
· Stand-alone type main unit/expandable type main unit
when floor-mounted : 0 to 50°C
when panel-mounted : 0 to 50°C
· DS400/DS600 Subunit
when floor-mounted : 0 to 50°C
when panel-mounted : –10 to 60°C
Ambient humidity
20 to 80%RH for –10 to 40°C, 10 to 50%RH for 40 to 50°C, 5 to 30%RH for 50 to 60°C (no condensation)
Vibration
10 to 60Hz, 0.2m/s
2
Shock
not allowed
Magnetic field
400 A/m max (50/60 Hz)
Position
Mount the unit left-right horizontally or vertically, as a general rule.
Installation location
Room
Installation height
Altitude up to 2,000 m
Installation category based on IEC 1010-1
II*
1
Pollution degree based on IEC 1010-1
2*
2
Warm-up time
At least 30 minutes after power switch-on.
*
1
Installation category is the specification of the inpuls withstanding voltage which is also called
as overvoltage category.
*
2
Polution degree is the level of foreign body adhesion such as the solid, liquid, and gas which
decrease the withstanding voltage, 2 means general indoor atmosphere.
Standard Performance
Reference operation conditions
temperature: 23±2°C; humidity: 55 ±10% RH; supply voltage 90 to 250 VAC (AC power supply)
/10 to 32 VDC (DC power supply); supply frequency: 50/60 ±1% (AC power supply); warm-up
time: at least 30 minutes; when operating, the system must not adversely affect the operation of
other equipment.
Effect of Operating Conditions
Ambient temperature: variation for a temperature change of 10°C: within ±(0.1% of rdg + 1
digit); ±(0.2% of span + 1 digit) for Cu10Ω
Voltage variation: within ±1 digit over the range of 90 to 250 VAC (frequency 50/60 Hz, for AC
power supply) /10 to 32 VDC (for DC power supply)
External magnetic field: variation with respect to AC (50/60 Hz) and DC magnetic fields of 400
A/m: within ± (0.1% of rdg + 10 digits)
Except for the power monitor module: within ±15% of range
Signal source resistance: variation with respect to signal source resistance 1kΩ change
(1)voltage
2 V range or below: within ±10µV
6 V range or above: within ±0.1% of rdg
(2)thermocouple
within ±10µV; however it must be within ±100µV when burnout is specified.
(3)RTD
variation with respect to change of 10Ω per wire (when all wires have the same resistance
value)
indication: within ±(0.1% of rdg + 1 digit)
variation in indication with respect to a difference of 40 mΩ in the resistance between
conductors (max, difference between 3 wires): approx. 0.1°C (in case of Pt100)
Mounting position
Variation when the unit is mounted horizontally on a panel: within ±(0.1% of rdg + 1 digit)
Vibration
Variation when sinusoidal vibration of acceleration 0.2 m/s
2
is applied for two hours in each of
the 3 axial directions over a frequency range of 10 to 60 Hz: within ±(0.1% of rdg + 1 digit)
4.1 DA100/ DS400/ DS600
- Data Acquisition Unit 1
- Foreword 2
- Trademarks 2
- Revisions 2
- About the Style Number 3
- Main Unit DA100 4
- Subunit DS400/DS600 4
- Input Modules 5
- Standard Accessories 6
- Optional Accessories 7
- Software 7
- How to Use this Manual 9
- Contents 10
- 1.1 About DARWIN 11
- Connection example 13
- Subunit DS400 14
- Subunit DS600 15
- Input modules 15
- Wire clip 16
- Clamp terminal 16
- Screw terminal 17
- I/O Terminal Modules 18
- Extender Module/Extender Base 20
- Safety Precautions 22
- General Handling Precautions 22
- 2.2 How to Install the DA100 23
- M4 Screws 24
- Name Part No. Description 24
- Modules Which Can be Used 26
- GP-IB module 28
- Ferrite core 28
- RS-422-A/RS-485 31
- Ethernet 33
- Extension Cables 34
- Connecting Procedure 34
- W WARNING 35
- Terminal cover 36
- Screws for fastenin 36
- the cover 36
- Terminals 37
- Wiring Diagram 37
- Installation and Wiring 40
- • Four-gauge method 40
- Installing an Extension Base 44
- Power ON/OFF 46
- Switching the Power ON/OFF 47
- Soldering 48
- - (0 V DC) 48
- + (10 to 32 V DC) 48
- 2.9 Countering Noise 50
- Propagation of Noise 51
- Frequency (Hz) 54
- Signal lines 55
- Power lines 55
- Φ = strong 56
- Φ = weak 56
- Connected 57
- 3.1 Diagnosis 60
- How to Cope with Errors 61
- 3.2 Error Messages 62
- Error message<Logger> 63
- 3.2 Error Messages 64
- 3.3 Trouble-Shooting 67
- About Fuse Replacement 68
- About Calibration 68
- Input terminal 69
- 4.1 DA100/ DS400/ DS600 70
- Construction 71
- Sum Cumulative Sum 73
- Power Supply 75
- Normal Operation Conditions 75
- Standard Performance 76
- Other Specifications 77
- Ranges of Indication 85
- 4.8 Alarm Output Module 93
- 4.9 DI/DO Module 94
- General Specifications 95
- RS-232-C Module 95
- 4.11 Retransmission Module 98
- 4.13 Dimensional Drawings 100
- 4.13 Dimensional Drawings 101
- Power Monitor Module 102
- Pulse Input Module 103
- Digital Input Module 103
- GP-IB Module 104
- RS-232C Module 104
- RS-422-A/RS-485 Module 105
- Ethernet Module 105
- 1-5 V Retransmission Module 106
- 4-20 mA Retransmittion Module 106
- Extension Module 107
- Extension Base 107
- IM DA100-01E 108
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.260 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels