Yokogawa DA100 Manuel d'utilisateur Page 64
- Page / 109
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-01E
3-5
3
Trouble-shooting and Maintenance
3.2 Error Messages
Error message<Software Configuration>
No. Error/Corrective Action
E3301 Failed to scan.
Check that the DARWIN is turned ON, the communication module is being recognized by the DARWIN (DR/DC), and the
cable is connected properly.
In addition, check the following items according to the communication methods.
For GPIB
Is the address correct? Is the driver is properly installed? Is the GPIB card manufactured by NI?
For Ether
Is the address correct? Is the TCP/IP protocol installed in Windows? Is the Ether card properly installed?
For RS-232-C, RS-422-A, and RS-485
Is the baud rate correct? Is the port (COM1 to COM4) correct? Is the address correct (RS422)? Is the PC's serial port
functioning? Is the correct type of cable being used?
E3302 Failed to reconstruct
See the corrective actions for E3301.
E3303 Failed to initialize
See the corrective actions for E3301.
E3312 Select all ranges that has invalid values.
Even though there is a range with an invalid calibration value, that range is not selected. Select the range with the invalid
calibration value and calibrate it.
E3313 Failed to calibrate.
Check that the module is connected properly. Check the wiring, rated input, and etc.
E3314 For xxx is invalid.
Enter the correct value.
E3331 There is no module. Or there are many modules.
Several modules exist when setting up the network. Specify only one module.
E3337 The address is invalid.
Properly set the combination of the IP address, subnet mask, and default gateway.
E3338 Can not set the network address.
An error occurred while setting the address.
E3339 Modules not found.
Set the module's dipswitch and turn DARWIN ON.
Check that the cables are connected properly.
Error message<Historical Viewer >
No. Error/Corrective Action
E3101 Data is not exist.
Valid data do not exist.
E3102 Channel is not exist
Valid channel does not exist.
- Data Acquisition Unit 1
- Foreword 2
- Trademarks 2
- Revisions 2
- About the Style Number 3
- Main Unit DA100 4
- Subunit DS400/DS600 4
- Input Modules 5
- Standard Accessories 6
- Optional Accessories 7
- Software 7
- How to Use this Manual 9
- Contents 10
- 1.1 About DARWIN 11
- Connection example 13
- Subunit DS400 14
- Subunit DS600 15
- Input modules 15
- Wire clip 16
- Clamp terminal 16
- Screw terminal 17
- I/O Terminal Modules 18
- Extender Module/Extender Base 20
- Safety Precautions 22
- General Handling Precautions 22
- 2.2 How to Install the DA100 23
- M4 Screws 24
- Name Part No. Description 24
- Modules Which Can be Used 26
- GP-IB module 28
- Ferrite core 28
- RS-422-A/RS-485 31
- Ethernet 33
- Extension Cables 34
- Connecting Procedure 34
- W WARNING 35
- Terminal cover 36
- Screws for fastenin 36
- the cover 36
- Terminals 37
- Wiring Diagram 37
- Installation and Wiring 40
- • Four-gauge method 40
- Installing an Extension Base 44
- Power ON/OFF 46
- Switching the Power ON/OFF 47
- Soldering 48
- - (0 V DC) 48
- + (10 to 32 V DC) 48
- 2.9 Countering Noise 50
- Propagation of Noise 51
- Frequency (Hz) 54
- Signal lines 55
- Power lines 55
- Φ = strong 56
- Φ = weak 56
- Connected 57
- 3.1 Diagnosis 60
- How to Cope with Errors 61
- 3.2 Error Messages 62
- Error message<Logger> 63
- 3.2 Error Messages 64
- 3.3 Trouble-Shooting 67
- About Fuse Replacement 68
- About Calibration 68
- Input terminal 69
- 4.1 DA100/ DS400/ DS600 70
- Construction 71
- Sum Cumulative Sum 73
- Power Supply 75
- Normal Operation Conditions 75
- Standard Performance 76
- Other Specifications 77
- Ranges of Indication 85
- 4.8 Alarm Output Module 93
- 4.9 DI/DO Module 94
- General Specifications 95
- RS-232-C Module 95
- 4.11 Retransmission Module 98
- 4.13 Dimensional Drawings 100
- 4.13 Dimensional Drawings 101
- Power Monitor Module 102
- Pulse Input Module 103
- Digital Input Module 103
- GP-IB Module 104
- RS-232C Module 104
- RS-422-A/RS-485 Module 105
- Ethernet Module 105
- 1-5 V Retransmission Module 106
- 4-20 mA Retransmittion Module 106
- Extension Module 107
- Extension Base 107
- IM DA100-01E 108
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.534 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels