Yokogawa DA100 Manuel d'utilisateur Page 67
- Page / 109
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM DA100-01E
3-8
3.3 Trouble-Shooting
• When a message appears on the screen, first refer to the list of error messages described on page
3-4.
• When servicing is necessary, contact your nearest sales representative. Addresses may be found
on the back cover of this manual.
Description Cause Action Reference
Page
No power-up; the status The used power supply lies Use the correct power supply. 2-25
indicator does not light. outside the permissible range.
The status indicator is The communication module Configure the communication 2-4
flashing in 1-second is not configured properly. module properly.
intervals.
The status indicator is An internal error occurred. Turn the power OFF and 2-25
flashing in an interval ON again.
other than 1-second.
Connected sub-units are The power of the corresponding Turn the power ON. 2-25
not recognized. sub-unit has been turned OFF.
The extension cables of the Connect the extension cables 2-13
corresponding sub-unit are not properly.
connected properly.
Connected modules are The corresponding module is not Connect the module properly. 2-4
not recognized. properly connected.
Measurement values are The input does not conform Verify the input Chapter 4
not correct. specifications. specifications.
The measurement mode is not Select a suitable measurement *1
suited for this input. mode.
The measurement range/span/scale Select a suitable measurement *1
setting is not suited for this input. range/span/scale.
Noise interference. Apply anti-noise measures. 2-29
Input wiring is not correct. Wire the input properly. 2-15
RJC settings are not correct. Enter the correct RJC settings. *1
The environmental temperature Make sure the environmental 2-2
is outside the specifications. temperature matches the
specifications.
*1 Refer to the User’s Manual for DAQ Software 32.
- Data Acquisition Unit 1
- Foreword 2
- Trademarks 2
- Revisions 2
- About the Style Number 3
- Main Unit DA100 4
- Subunit DS400/DS600 4
- Input Modules 5
- Standard Accessories 6
- Optional Accessories 7
- Software 7
- How to Use this Manual 9
- Contents 10
- 1.1 About DARWIN 11
- Connection example 13
- Subunit DS400 14
- Subunit DS600 15
- Input modules 15
- Wire clip 16
- Clamp terminal 16
- Screw terminal 17
- I/O Terminal Modules 18
- Extender Module/Extender Base 20
- Safety Precautions 22
- General Handling Precautions 22
- 2.2 How to Install the DA100 23
- M4 Screws 24
- Name Part No. Description 24
- Modules Which Can be Used 26
- GP-IB module 28
- Ferrite core 28
- RS-422-A/RS-485 31
- Ethernet 33
- Extension Cables 34
- Connecting Procedure 34
- W WARNING 35
- Terminal cover 36
- Screws for fastenin 36
- the cover 36
- Terminals 37
- Wiring Diagram 37
- Installation and Wiring 40
- • Four-gauge method 40
- Installing an Extension Base 44
- Power ON/OFF 46
- Switching the Power ON/OFF 47
- Soldering 48
- - (0 V DC) 48
- + (10 to 32 V DC) 48
- 2.9 Countering Noise 50
- Propagation of Noise 51
- Frequency (Hz) 54
- Signal lines 55
- Power lines 55
- Φ = strong 56
- Φ = weak 56
- Connected 57
- 3.1 Diagnosis 60
- How to Cope with Errors 61
- 3.2 Error Messages 62
- Error message<Logger> 63
- 3.2 Error Messages 64
- 3.3 Trouble-Shooting 67
- About Fuse Replacement 68
- About Calibration 68
- Input terminal 69
- 4.1 DA100/ DS400/ DS600 70
- Construction 71
- Sum Cumulative Sum 73
- Power Supply 75
- Normal Operation Conditions 75
- Standard Performance 76
- Other Specifications 77
- Ranges of Indication 85
- 4.8 Alarm Output Module 93
- 4.9 DI/DO Module 94
- General Specifications 95
- RS-232-C Module 95
- 4.11 Retransmission Module 98
- 4.13 Dimensional Drawings 100
- 4.13 Dimensional Drawings 101
- Power Monitor Module 102
- Pulse Input Module 103
- Digital Input Module 103
- GP-IB Module 104
- RS-232C Module 104
- RS-422-A/RS-485 Module 105
- Ethernet Module 105
- 1-5 V Retransmission Module 106
- 4-20 mA Retransmittion Module 106
- Extension Module 107
- Extension Base 107
- IM DA100-01E 108
Produits connexes et manuels pour Capteurs Yokogawa DA100
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(103 pages)
(103 pages)
Capteurs Yokogawa µR10000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(121 pages)
(121 pages)
Capteurs Yokogawa µR20000 Manuel d'utilisateur
(263 pages)
(263 pages)
Capteurs Yokogawa DR240 Manuel d'utilisateur
(293 pages)
(293 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.806 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels