Yokogawa Integral Oxygen Analyzer ZR202 Manuel d'utilisateur Page 105
- Page / 169
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IM 11M13A01-04E
8-17
8. Detailed Data Setting
For liquid fuel
Amount of water vapor in exhaust gas (Gw) = (1/100) {1.24 (9h + w)} [m /kg]
Theoretical amount of air (Ao) = {(12.38 / 10000) x H1}
2
1.36 [m /kg]
Low calorific power = H1
X value = {(3.37 / 10000) x Hx}
2
2.55 [m
3
/kg]
where, H1: low calorific power of fuel
h: Hydrogen in fuel (weight %)
w: Moisture content in fuel (weight %)
Hx: Same as numeric value of H1
For gaseous fuel
Amount of water vapor in exhaust gas = (1/100) {(h2) + 1/2 Sy (Cy hy) + w} [m /m ]
Theoretical amount of air = 11.2 x (H1/10000) [m /m ]
Low calorific power = H1
X value = (1.05 / 10000) x Hx [m /m ]
where, H1: low calorific power of fuel
h: Hydrogen in fuel (weight %)
w: Moisture content in fuel (weight %)
Hx: Same as numeric value of H1
For solid fuel
Amount of water vapor in exhaust gas (Gw) = (1/100) {1.24 (9h + w)} [m /kg]
Theoretical amount of air = {(1.01 x (H1 / 1000)} + 0.56 [m /kg]
Low calorific power = H1 = Hh
2
25 (9h + w) [kJ/kg]
X value = 1.11 - (0.106 / 1000 ) x Hx [m /m ]
where, w: Total moisture content in use (weight %)
h: Hydrogen content (weight %)
The average hydrogen content of coal mined in Japan, which is a dry ash-free type, is
5.7 %. Accordingly, "h" may be expressed mathematically by:
h = 5.7 [{100
2
(w + a)} / 100] x (100
2
w) / (100
2
w1)
where, a: Ash content [%]
w1: Moisture content [%], analyzed on a constant humidity basis
Hh: Higher calorific power of fuel [kJ/kg]
H1: Low calorific power of fuel [kJ/kg]
Hx: Same numeric value of H1
3
3
3
3
3
3
3
3
3
3
3
3
Figure 8.3 Fuel Calculation Formula
- User's 1
- Introduction 2
- r ATEX Documentation 4
- (1) About This Manual 6
- Oxygen Analyzer 9
- IM 11M13A01-04E 10
- Contents 11
- 1. Overview 15
- 1.1.1 System 1 16
- 1.1.2 System 2 17
- 1.2.1 System Components 18
- 2. Specifications 19
- 2.1 General Specifications 20
- No.KEMA 04ATEX 21
- EEx d IIB+H 21
- ENCLOSURE: IP66 21
- The country of origin 22
- 2. Specifications 23
- Model and Suffix code 26
- • External Dimensions 27
- • Standard Accessories 28
- • Hood (Option code /H) 29
- 2.1.3 ZO21R-L Probe Protector 30
- 2.2 ZA8F Flow Setting Unit 31
- 2.3 ZO21S Standard Gas Unit 33
- Unit: mm 34
- 2.4 Other Equipment 35
- T2.13E.EPS 37
- 3. Installation 41
- Hazardous Area Division 1 43
- 3. Installation 45
- 3.1.6 Probe Insertion Hole 46
- F3.12E.EPS 48
- F3.14E.EPS 49
- 4. Piping 51
- 4.1 Piping for System 1 52
- 4. Piping 53
- 4.2 Piping for System 2 54
- Piping Diagram 56
- 5. Wiring 57
- 5.1.2 Wiring 58
- 5.2 Wiring for Analog Output 59
- 5.3.1 Wiring for Power Line 60
- 5.4 Wiring for Contact Output 61
- 5.5 Contact Input Wiring 62
- 6.1 ZR202S Oxygen Analyzer 63
- Horizontal 64
- Vertical 64
- 7. Startup 65
- 7.2 Valve Setup 66
- 7.4.1 Display and Switches 67
- 7.4.2 Display Configuration 69
- Table7.4 Parameter Code 71
- 7.4.5 Changing Set Values 72
- 7.7 Output Range Setting 76
- 7. Startup 77
- Switch operation 78
- Display Description 78
- 7.9 Checking Contact I/O 79
- 7.9.1 Contact Output Check 80
- 7.9.3 Checking Input Contacts 82
- 7.10 Calibration 83
- 7.10.2 Manual Calibration 85
- 8. Detailed Data Setting 89
- T8.1E.EPS 89
- 8.2 Current Output Setting 90
- 8.2.4 Default Values 91
- 8.3 Output Hold Setting 92
- 8.3.3 Output Hold Setting 94
- 8.3.4 Default Values 94
- 8.4.1 Alarm Values 95
- 8.4.2 Alarm Output Actions 95
- 8.4.3 Alarm Setting 96
- 8.4.4 Default Values 97
- 8.5 Output Contact Setup 98
- Set item Parameter Set value 99
- Output contact 1 99
- T8.10E.EPS 99
- 8.5.3 Default Values 100
- 8.6 Input Contact Settings 101
- Omitted here 102
- 8. Detailed Data Setting 103
- 8.7.3 Setting Fuels 104
- For solid fuel 105
- For liquid fuel 105
- For gaseous fuel 105
- Absolute 106
- Dry-bulb temperature, 8C 106
- Table 8.16 Fuel Data 107
- T8.17E.EPS 108
- 9. Calibration 109
- 9.1.2 Calibration Gas 110
- 9.1.3 Compensation 111
- 9.2 Calibration Procedures 113
- 9. Calibration 115
- 9.2.1.7Default Values 116
- 9.2.2 Calibration 117
- 10. Other Functions 119
- 10.1.1 Air Ratio 121
- 10.1.2 Cell Temperature 121
- 10.1.3 C. J. Temperature 121
- T10.2E.EPS 122
- 10.1.9 Response Time 123
- 10.1.11 Robustness of a Cell 123
- F10.3E.EPS 125
- 10.3 Initialization Procedure 127
- 10.4 Reset 128
- Table: Resetting 129
- Table 10.6 Parameter Codes 130
- T10.6E.EPS 134
- F10.14E.EPS 137
- 10.5.3 Calibration Gas Flow 138
- Calibration gas tube 144
- Exploded view of components 144
- (with outside diameter 144
- Groove in which the contact 146
- (E7042BS) is placed 146
- View A-A 148
- 11.1.5 Replacement of O-ring 150
- 11.2.1 Replacing Fuses 151
- Vertical mounting 153
- Horizontal mounting 153
- Fixing screw pairs 153
- 155
- F12.2E.EPS 156
- F12.3E.EPS 157
- 12.2.1 What is an Alarm? 158
- Oxygen concentration (% O 159
- ) Cell voltage (mV) 159
- 1% 67.1 159
- 12. Troubleshooting 161
- Customer 165
- Maintenance 165
- Parts List 165
- CMPL 11M13A01-04E 167
- Revision Record 169
Produits connexes et manuels pour Équipement aérien Yokogawa Integral Oxygen Analyzer ZR202
(157 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.915 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels