Yokogawa ADMAG AXR Manuel d'utilisateur Page 73
- Page / 194
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
<6. PARAMETER DESCRIPTION>
6-25
IM 01E30D01-01EN
(5) Menu F: Status Function Setting items
Menu F contains setting items relevant to status Output functions.
[F10: DO Function] Setting of the function for the DO output terminal
This parameter sets the function for the DO (digital output) terminal.
Setting Function Description
No Function Stops output (i.e., inactive condition) As no function is set, there is no output.
Pulse Output Pulse output Pulse output is carried out.
Alarm Output Output upon alarm Refer to Alarms (Section 6.5).
Warning Output Output upon warning
Total Switch Totalization switch output Status output is carried out when the forward internal totalized value
reaches or exceeds the totalization switch value. The totalization switch
value is determined using D23: Ttl Switch Lower and D24: Ttl Switch
Upper.
H/L Alarm H/L alarm output S
tatusoutputiscarriedoutwhentheinstantaneousowrateequalsor
fallsbelowthelowowratelimit(L),orwhenitequalsorexceedsthe
highowratelimit(H).TheselimitvaluesaredeterminedusingG10: Low
Alarm and G11: High Alarm.
Fwd/Rev Rngs F
orward/reverseowrate
measurement
Whenowisinthereversedirection,switchingtothereverserangeis
carried out automatically, measurement is performed, and status output is
carried out.
Auto 2 Rngs Automatic 2 ranges switching T
hisfunctionensuresthatwhentheinstantaneousowrateexceeds
100% of the range, transition to the next range is carried out automatically.
Status output is carried out upon range switching.
Example 2: When the “Alarm Output” function is
selected for the DO terminal, the following
signals are output from the terminal.
[F11]
setting
Function
DO status
output
Closed (On)
Active
Alarm (Alarm status) Closed
Good (Normal) Open
Open (Off)
Active
Alarm (Alarm status) Open
Good (Normal) Closed
Example 3: When the “Total Switch” function is
selected for the DO terminal, the following
signals are output from the terminal.
[F11]
setting
Function
DO status
output
Closed (On)
Active
Equal or above setting value Closed
Below setting value Open
Open (Off)
Active
Equal or above setting value Open
Below setting value Closed
[F11: DO Active Mode] Setting of the active mode
for DO terminal
Operations are performed in accordance with the
following table when the active mode has been
set to “Closed (On) Act” using this parameter.
Operating patterns are reversed when the active
mode has been set to “Open (Off) Act.”
Selected function
Condition of DO terminal
Open (Off) Closed (On)
Pulse Output
(see Example 1)
Open (Off) when
pulses are output.
Closed (On) when
pulses are output.
Alarm Output
(see Example 2)
Good (normal) Alarm status
Warning Output Good (normal) Warning status
Total Switch
(see Example 3)
Below setting value Equal or above
setting value
H/L Alarm Normal H/L alarm status
Fwd/Rev Rngs Forward direction Reverse direction
N
ote: For “Auto 2 Rngs” see the Multiple ranges setting
section.
Example 1: When the “Pulse Output” function is
selected for the DO terminal and the
E12: Pulse Width is “1 ms”, the following
signals are output from the terminal.
[F11]
setting
Function
DO status
output
Closed (On)
Active
Pulse output condition (1 ms) Closed
Pulse disable condition Open
Open (Off)
Active
Pulse output condition (1 ms) Open
Pulse disable condition Closed
- IM 01E30D01-01EN 1
- Contents 2
- EQUIPMENT 6
- 1. INTRODUCTION 7
- 1.1 Using the Magnetic 8
- Flowmeter Safely 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. HANDLING PRECAUTIONS 11
- 2.4 Installation Location 12
- Precautions 12
- 3. INSTALLATION 13
- 3.2.1 General Precautions 15
- 40 mm (1.5 in.), Wafer Type 17
- <3. INSTALLATION> 18
- 4. WIRING 25
- Waterproof gland 26
- Drain valve 27
- F0406.ai 27
- 4.4 Grounding Connection 28
- 4.5 Wiring Connections 29
- 4.6 Wiring Procedure 30
- <4. WIRING> 32
- Magnetic 34
- Recorder 35
- AXR Terminal 36
- Distributor, etc 37
- (5) Installing the Cover 39
- (USING THE DISPLAY UNIT) 40
- F0501.EPS 41
- 5.1 Operating Panel 41
- CongurationandFunctions 41
- SETESC INC 42
- DEC/SHIFT 42
- P:Protect 43
- B:Easy Setup 43
- C:Basic Setup 43
- 5.2.2 Setting Mode 44
- F0504-2.EPS 45
- F0505-2.ai 47
- F0506-1.ai 47
- F0506-2.ai 48
- 6. PARAMETER DESCRIPTION 49
- 6.3 Parameter List Overview 50
- 6.4 Parameter Description 64
- Setting Function 67
- No Execution No execution 67
- Meter factors 68
- Upper 2 digits 71
- Lower 6 digits 71
- Ranges Switching 74
- 5.6mA(10%) 80
- 18.4mA(90%) 81
- Default setting (Enable) 88
- Write protection (Protect) 88
- Default setting 88
- After password setting 88
- 6.5 Alarm Functions 89
- 6.5.4 NE-107 status 94
- 7.1 BT200 Basic Operations 95
- ( B ) ( y )( o ) 96
- ( m )( I ) 96
- 7.2.1 BT200 Connection 97
- ( ) key 98
- ( ) 98
- “FI-1101” to “FI-1201.” 102
- XXX…XX 103
- 5: HART 5 103
- 7: HART 7 103
- Distributor 104
- 8.6 Data Renewing 105
- 8.4 Basic Setup 105
- 8.5 ParametersConguration 105
- 8.8 HARTSpecicFunctions 106
- 8.8.2 Fixed Current Output 107
- 8.8.3 Burst Mode 107
- 8.8.4 Multidrop Mode 107
- (continued on next page) 110
- IMPORTANT 121
- Device Information 122
- 9.8 HARTSpecicFunctions 123
- 9.8.2 Trim Analog Output 124
- 9.8.3 Burst Mode 125
- 9.8.3.2EventNotication 128
- 9.8.4 Multidrop Mode 129
- F0910.ai 135
- 10. ACTUAL OPERATION 138
- 21:Adjustment 20mA 139
- M:Adjustment 140
- 10:Auto Zero Exe 140
- 11:Autozero Time 140
- Now Auto Zero 140
- Executing 140
- 11. MAINTENANCE 141
- 11.2 Components Replacement 142
- <11. MAINTENANCE> 143
- 11.3 Setting of Switches 145
- 11.4 Adhesion diagnostic 146
- Dielectric Strength Test 149
- 11.7 Troubleshooting 150
- 11.7.2 Unstable Zero 151
- 12. OUTLINE 153
- Alarms and Setting Alarms 155
- Flowtubes 156
- HAZARDOUS AREA CLASSIFICATION 157
- Spaninm/s(ft/s) 158
- 25 to 50 mm (1.0 to 2.0 in.) 160
- (flange type, wafer type) 160
- 65 to 200 mm (2.5 to 8.0 in.) 160
- <12. OUTLINE> 161
- Electrical 167
- Connection 167
- Indicator 167
- Electrical Connection 167
- Unit: mm (approx. inch) 171
- General-purpose Use; 176
- Explosion Proof Type; 176
- INSTRUMENT 178
- Terminals 179
- 14.2 FM 180
- 14.3 IECEx 181
- 14.4 TIIS 183
- Digital output circuit 185
- Supply/ Output signal circuit 185
- Installation 186
- A1.2.7 Startup Time 187
- A1.2.8 Firmware Update 187
- A1.2.9 Reliability Data 187
- A1.3 Denitionsand 188
- Abbreviations 188
- A1.3.2 Abbreviations 189
- FOR TIIS FLAMEPROOF EQUIPMENT 190
- Apparatus 191
- 5. External Wiring for 191
- Flameproof Apparatus 191
- 7. Selection of Cable Entry 193
- Devices for Flameproof Type 193
- Revision Information 194
Produits connexes et manuels pour Capteurs Yokogawa ADMAG AXR
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(112 pages)
(112 pages)
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(133 pages)
(133 pages)
Capteurs Yokogawa AXFA14G/C Manuel d'utilisateur
(123 pages)
(123 pages)
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(107 pages)
(107 pages)
Capteurs Yokogawa RAGN Manuel d'utilisateur
(46 pages)
(46 pages)
Capteurs Yokogawa RAKD Manuel d'utilisateur
(72 pages)
(72 pages)
Capteurs Yokogawa RAMC Manuel d'utilisateur
(136 pages)
(136 pages)
Keurig B50 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour la préparation du café Keurig B50.
Nous fournissons des manuels en pdf 1 Keurig B50 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels