Yokogawa ADMAG AXR Manuel d'utilisateur Page 63
- Page / 194
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
<6. PARAMETER DESCRIPTION>
6-15
IM 01E30D01-01EN
(13) Item P (Menu P): Parameter Protection items
Menu P contains items that are relevant to write protection and passwords.
Item
Name
R
/W
Data range
Units
Position
of decimal
point
Default value
(*): Indicated item
Description
Display unit
(BRAIN)
Display unit
/
BRAIN
P00 Protect
(PROTECT)
P10 Key Code
(KEY CODE)
W 0 to 9999 0 Parameter of the display
restriction
P20 Write Protect
(W PROTECT)
R No
Yes
No Displays whether or not
overwriting of parameter data is
prohibited.
P21 Enable Wrt Passwd
(ENABLE WRITE)
W ASCII 8 characters Sets the correct password so
that write protection function
will be released.
P22 New Password
(NEW PASSWORD)
W ASCII 8 characters Sets the password for write
protection funcion
P23 Software Seal
(SOFT SEAL)
R Break
Keep
Keep Displays whether or not a Joker
password was used (Break).
P60 —
(SELF CHECK)
R Good
Error
See “6.5 Alarm Functions”.
- IM 01E30D01-01EN 1
- Contents 2
- EQUIPMENT 6
- 1. INTRODUCTION 7
- 1.1 Using the Magnetic 8
- Flowmeter Safely 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. HANDLING PRECAUTIONS 11
- 2.4 Installation Location 12
- Precautions 12
- 3. INSTALLATION 13
- 3.2.1 General Precautions 15
- 40 mm (1.5 in.), Wafer Type 17
- <3. INSTALLATION> 18
- 4. WIRING 25
- Waterproof gland 26
- Drain valve 27
- F0406.ai 27
- 4.4 Grounding Connection 28
- 4.5 Wiring Connections 29
- 4.6 Wiring Procedure 30
- <4. WIRING> 32
- Magnetic 34
- Recorder 35
- AXR Terminal 36
- Distributor, etc 37
- (5) Installing the Cover 39
- (USING THE DISPLAY UNIT) 40
- F0501.EPS 41
- 5.1 Operating Panel 41
- CongurationandFunctions 41
- SETESC INC 42
- DEC/SHIFT 42
- P:Protect 43
- B:Easy Setup 43
- C:Basic Setup 43
- 5.2.2 Setting Mode 44
- F0504-2.EPS 45
- F0505-2.ai 47
- F0506-1.ai 47
- F0506-2.ai 48
- 6. PARAMETER DESCRIPTION 49
- 6.3 Parameter List Overview 50
- 6.4 Parameter Description 64
- Setting Function 67
- No Execution No execution 67
- Meter factors 68
- Upper 2 digits 71
- Lower 6 digits 71
- Ranges Switching 74
- 5.6mA(10%) 80
- 18.4mA(90%) 81
- Default setting (Enable) 88
- Write protection (Protect) 88
- Default setting 88
- After password setting 88
- 6.5 Alarm Functions 89
- 6.5.4 NE-107 status 94
- 7.1 BT200 Basic Operations 95
- ( B ) ( y )( o ) 96
- ( m )( I ) 96
- 7.2.1 BT200 Connection 97
- ( ) key 98
- ( ) 98
- “FI-1101” to “FI-1201.” 102
- XXX…XX 103
- 5: HART 5 103
- 7: HART 7 103
- Distributor 104
- 8.6 Data Renewing 105
- 8.4 Basic Setup 105
- 8.5 ParametersConguration 105
- 8.8 HARTSpecicFunctions 106
- 8.8.2 Fixed Current Output 107
- 8.8.3 Burst Mode 107
- 8.8.4 Multidrop Mode 107
- (continued on next page) 110
- IMPORTANT 121
- Device Information 122
- 9.8 HARTSpecicFunctions 123
- 9.8.2 Trim Analog Output 124
- 9.8.3 Burst Mode 125
- 9.8.3.2EventNotication 128
- 9.8.4 Multidrop Mode 129
- F0910.ai 135
- 10. ACTUAL OPERATION 138
- 21:Adjustment 20mA 139
- M:Adjustment 140
- 10:Auto Zero Exe 140
- 11:Autozero Time 140
- Now Auto Zero 140
- Executing 140
- 11. MAINTENANCE 141
- 11.2 Components Replacement 142
- <11. MAINTENANCE> 143
- 11.3 Setting of Switches 145
- 11.4 Adhesion diagnostic 146
- Dielectric Strength Test 149
- 11.7 Troubleshooting 150
- 11.7.2 Unstable Zero 151
- 12. OUTLINE 153
- Alarms and Setting Alarms 155
- Flowtubes 156
- HAZARDOUS AREA CLASSIFICATION 157
- Spaninm/s(ft/s) 158
- 25 to 50 mm (1.0 to 2.0 in.) 160
- (flange type, wafer type) 160
- 65 to 200 mm (2.5 to 8.0 in.) 160
- <12. OUTLINE> 161
- Electrical 167
- Connection 167
- Indicator 167
- Electrical Connection 167
- Unit: mm (approx. inch) 171
- General-purpose Use; 176
- Explosion Proof Type; 176
- INSTRUMENT 178
- Terminals 179
- 14.2 FM 180
- 14.3 IECEx 181
- 14.4 TIIS 183
- Digital output circuit 185
- Supply/ Output signal circuit 185
- Installation 186
- A1.2.7 Startup Time 187
- A1.2.8 Firmware Update 187
- A1.2.9 Reliability Data 187
- A1.3 Denitionsand 188
- Abbreviations 188
- A1.3.2 Abbreviations 189
- FOR TIIS FLAMEPROOF EQUIPMENT 190
- Apparatus 191
- 5. External Wiring for 191
- Flameproof Apparatus 191
- 7. Selection of Cable Entry 193
- Devices for Flameproof Type 193
- Revision Information 194
Produits connexes et manuels pour Capteurs Yokogawa ADMAG AXR
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(112 pages)
(112 pages)
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(133 pages)
(133 pages)
Capteurs Yokogawa AXFA14G/C Manuel d'utilisateur
(123 pages)
(123 pages)
Capteurs Yokogawa ADMAG AXF Manuel d'utilisateur
(107 pages)
(107 pages)
Capteurs Yokogawa RAGN Manuel d'utilisateur
(46 pages)
(46 pages)
Capteurs Yokogawa RAKD Manuel d'utilisateur
(72 pages)
(72 pages)
Capteurs Yokogawa RAMC Manuel d'utilisateur
(136 pages)
(136 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.235 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels