Yokogawa FieldMate Manuel d'utilisateur

User’sManualAXFVerication ToolIM 01R01A11-01ENIM 01R01A11-01EN1st EditionR2.05R1.01

<2 OUTILINE>2-2IM 01R01A11-01EN2.1 CongurationThe following equipment is required to use Verication Tool ver. 1.01.00;• YOKOGAWA magnet

<2 OUTILINE>2-3IM 01R01A11-01EN2.2 Verication ItemThis Verication Tool has 2 modes, which can be run separately.1. Standard Verication

<2 OUTILINE>2-4IM 01R01A11-01EN2.3 Operation ProcedureFigure 2.3.1 summarizes operation procedure. To complete “Standard VF”, start-up Ver

<3 PREPARATION>3-1IM 01R01A11-01EN3 PREPARATIONWARNING • Before running the Verication Tool, loop should be set to manual mode in the ho

<3 PREPARATION>3-2IM 01R01A11-01EN3.1 Package and InstallationRegarding the packaging and installation procedure, refer to IM 01R01A01-01E

<3 PREPARATION>3-3IM 01R01A11-01EN3.2.2 During Verication1) If the AXF write protect function is set to “Protect” during the verication

Blank Page

<4 START-UP FROM FieldMate>4-1IM 01R01A11-01EN4 START-UP FROM FieldMateVerication Tool can be started by the following: From “Segment V

<4 START-UP FROM FieldMate>4-2IM 01R01A11-01EN4.1 From “Segment Viewer” (AXF is reading in “online” mode in FieldMate)NOTESet the device a

<4 START-UP FROM FieldMate>4-3IM 01R01A11-01EN(B) By selecting menu “Action”Select the target (AXF) icon displayed at “Segment Viewer”, an

Blank Page

<4 START-UP FROM FieldMate>4-4IM 01R01A11-01EN4.2 From “Device Navigator”NOTEWhen Verication Tool is started from “Device Navigator”, it

<4 START-UP FROM FieldMate>4-5IM 01R01A11-01EN(B) By selecting menu “Action”Select the target (AXF) icon displayed at “Device Navigator”,

<4 START-UP FROM FieldMate>4-6IM 01R01A11-01EN4.3 From “Verication Data” in “Device Maintenance Info”NOTEWhen Verication Tool is started

<4 START-UP FROM FieldMate>4-7IM 01R01A11-01EN(B) By selecting menu “Action”In the “Device Maintenance Info” menu bar, select “Action”-“Vi

<4 START-UP FROM FieldMate>4-8IM 01R01A11-01EN4.4 From “History”NOTEWhen Verication Tool is started from “History”, it will be in “ofine

<4 START-UP FROM FieldMate>4-9IM 01R01A11-01EN(B) By selecting menu “Action”Select the target (AXF) listed in “Device Maintenance Info”, a

Blank Page

<5 LAUNCHING>5-1IM 01R01A11-01EN5 LAUNCHINGWhen Verication Tool is launched, Figure 5.1.1 is displayed automatically.F050101.aiFigure 5.1

<5 LAUNCHING>5-2IM 01R01A11-01EN5.1 Creating New Verication Data1) After the “Splash Screen”, 1)-1 When there is no existing vericati

<5 LAUNCHING>5-3IM 01R01A11-01EN2) “General Information” is displayed. See Figure 5.1.3. Enter each eld and click “Next (8)”. Figure 6.1

Toc-1IM 01R01A11-01ENAXFVerication ToolCONTENTSIM 01R01A11-01EN 1st Edition1 INTRODUCTION ...

<5 LAUNCHING>5-4IM 01R01A11-01EN5.2 Loading Existing Verication DataNOTEIn terms of keeping the integrity of the data, loaded verication

<5 LAUNCHING>5-5IM 01R01A11-01EN5.3 After Unexpected TerminationIn case of launching after an unexpected termination of the program, see 8

Blank Page

<6 OPERATION>6-1IM 01R01A11-01EN6 OPERATIONThis chapter describes how to use Verication Tool.For details of the verication procedure, se

<6 OPERATION>6-2IM 01R01A11-01EN6.1 Main ScreenThis screen performs the following actions: Loads the verication data. See 6.1.1. Save

<6 OPERATION>6-3IM 01R01A11-01EN6.1.1 Load1) Click the “Load” icon.F060102.aiFigure 6.1.2 “Load” Icon2) After clicking the “Load” icon,

<6 OPERATION>6-4IM 01R01A11-01EN6.1.2 SaveBy clicking the “Save” icon, the veri cation data is saved to the database.After clicking “Save

<6 OPERATION>6-5IM 01R01A11-01EN2) Save the data as “Read-only” or “Editable”.2)-1 To save the verication data as read-only: Click “OK”

<6 OPERATION>6-6IM 01R01A11-01EN(B) When “No Flow + Flow” is complete:1) After clicking the “Save” icon, Figure 6.1.9 is displayed.1 2 34

<6 OPERATION>6-7IM 01R01A11-01ENTable 6.1.6 “Conrm Replacing Data” DialogItem No.Item Name Description1 Yes Replace the data.2 No Cancels

Toc-2IM 01R01A11-01EN6.2 Standard VF ... 6-116.2.1

<6 OPERATION>6-8IM 01R01A11-01EN6.1.3 Print outTo print the result sheet, click the “Print” icon. Figure 6.1.14 is displayed.F060113.aiFig

<6 OPERATION>6-9IM 01R01A11-01EN6.1.4 Menu barThere are “File” and “Help” in the menu bar.(A) FileSelect the preferred menu.1234F060115.a

<6 OPERATION>6-10IM 01R01A11-01EN(B) HelpUpon selecting “About AXF Verication Tool…” in the “Help” menu, Figure 6.1.17 is displayed.1F060

<6 OPERATION>6-11IM 01R01A11-01EN6.2 Standard VF This mode veries the condition of the AXF without difculty, by checking its internal

<6 OPERATION>6-12IM 01R01A11-01EN6.2.1 “Circuit” check and “Device Status” check (Verication Tool is in “online” mode)CAUTION• “Circuit”

<6 OPERATION>6-13IM 01R01A11-01EN2345671F060202.aiFigure 6.2.2 “Circuit and Device Status” ScreenTable 6.2.2 “Circuit and Device Status” Sc

<6 OPERATION>6-14IM 01R01A11-01EN(2) Nominal size is over 400mm, without optional code ELC (DC Noise Cut Circuit)Item No.Item Name Descript

<6 OPERATION>6-15IM 01R01A11-01EN(A) No Flow (The uid velocity is completely zero)1) Fill the owtube with uid completely. Be sure that

<6 OPERATION>6-16IM 01R01A11-01EN12F060204.aiFigure 6.2.4 “No Flow Conrmation” DialogTable 6.2.4 “No Flow Conrmation” DialogItem No.Item

<6 OPERATION>6-17IM 01R01A11-01EN5) After the “Circuit” check and “Device Status” check are completed for the “No Flow” condi-tion, Figure

<1 INTRODUCTION>1-1IM 01R01A11-01EN1 INTRODUCTIONThis User’s Manual gives instructions on “AXF Verication Tool”.This software is used to

<6 OPERATION>6-18IM 01R01A11-01EN(B) Flow (The uid velocity is sufcient)1) Fill the owtube with uid. Be sure that the uid velocity i

<6 OPERATION>6-19IM 01R01A11-01EN12F060208.aiFigure 6.2.8 “Flow Conrmation” DialogTable 6.2.7 “Flow Conrmation” DialogItem No.Item Name D

<6 OPERATION>6-20IM 01R01A11-01EN5) After the “Circuit” check and the “Device Status” check are completed for the “Flow” condi-tion, Figur

<6 OPERATION>6-21IM 01R01A11-01EN6.2.2 Physical Appearance231F060211.aiFigure 6.2.11 “Physical Appearance” Screen Table 6.2.9 “Physical Ap

<6 OPERATION>6-22IM 01R01A11-01EN6.2.3 Standard VF ResultF060213.aiFigure 6.2.13 Example of “Result of Standard VF”

<6 OPERATION>6-23IM 01R01A11-01EN6.3 Enhanced VF• This mode provides more reliable verication by performed inspections equivalent to SER

<6 OPERATION>6-24IM 01R01A11-01ENTable 6.3.1 “Enhanced VF” ScreenItem No.Item Name Description1 Current OutputChecks the current output.See

<6 OPERATION>6-25IM 01R01A11-01EN6.3.1 Current Output This item checks the current output from the converter.31 24F060302.aiFigure 6.3.2 “

<6 OPERATION>6-26IM 01R01A11-01ENCurrent OutputUse a Yokogawa CA150 Handy Calibrator or similar.Set the Digital MultiMeter (CA150 or simila

<6 OPERATION>6-27IM 01R01A11-01EN1) Wire AXF and CA150 Handy Calibrator or similar as shown in Figure 6.3.3.2) Set a current value to out

<1 INTRODUCTION>1-2IM 01R01A11-01EN1.1 About This Manual• This manual should be provided to the end user.• Before using the AXF Vericat

<6 OPERATION>6-28IM 01R01A11-01EN6.3.2 Pulse OutputThis item checks the pulse output from the converter.Check the Suf x Code of AXF conve

<6 OPERATION>6-29IM 01R01A11-01EN(A) Pulse Output (without optional code EM)1) Wire AXF and CA150 Handy Calibrator or similar as shown in

<6 OPERATION>6-30IM 01R01A11-01ENNOTE Measure for more than 60 seconds. If using a YOKOGAWA CA150, set the mode to “Contact Input” and

<6 OPERATION>6-31IM 01R01A11-01EN7) End processing7)-1 When Verication Tool is in “online” mode: Click “Exit” in “Output Selection”.7)

<6 OPERATION>6-32IM 01R01A11-01EN(B) Active Pulse Output (with optional code EM)1) Wire AXF and CA150 Handy Calibrator or similar as show

<6 OPERATION>6-33IM 01R01A11-01ENNOTE• Measure for more than 60 seconds.• If using a YOKOGAWA CA150, set the mode to “Frequency (FREQ) an

<6 OPERATION>6-34IM 01R01A11-01EN7) End processing7)-1 When Verication Tool is in “online” mode: Click “Exit” in “Output Selection”.7)-

<6 OPERATION>6-35IM 01R01A11-01EN6.3.3 ConverterWARNING Follow User’s Manual FY2-XJAM012-40-2E for correct operation and safe handling.Thi

<6 OPERATION>6-36IM 01R01A11-01EN1) For details of the calibration procedures, follow User’s Manual FY2-XJAM012-40-2E. Record the followi

<6 OPERATION>6-37IM 01R01A11-01EN2)-2 When Verication Tool is in “ofine” mode: Read the value of parameter “Velocity Check” manually. R

<1 INTRODUCTION>1-3IM 01R01A11-01ENIMPORTANTAn IMPORTANT sign denotes that attention is required to avoid damage to the instrument or syste

<6 OPERATION>6-38IM 01R01A11-01EN6.3.4 Insulation ResistanceWARNING Follow User’s Manual IM 01E20D01-01E for correct operational and safe

<6 OPERATION>6-39IM 01R01A11-01EN6.4 ResultThe results of Standard VF and Enhanced VF are available in the “Result” tab. Uncompleted check

<6 OPERATION>6-40IM 01R01A11-01ENThe result in full view is shown Figure 6.4.2.If the user needs a hard copy of the report, refer to 6.1.3.

<6 OPERATION>6-41IM 01R01A11-01ENTable 6.4.1 ResultItem No.Item Name Description1Tag (Converter)Tag (Flowtube)Serial No. (Converter)Serial

Blank Page

<7 VARIATION OF VERIFICATION DATA>7-1IM 01R01A11-01EN7 VARIATION OF VERIFICATION DATAIn terms of keeping its own data integrity, veri cat

<7 VARIATION OF VERIFICATION DATA>7-2IM 01R01A11-01EN7.2 Locked Data“Locked data” is saved as read-only. The icon in Data Status is “ ”.Af

<8 TERMINATION>8-1IM 01R01A11-01EN8 TERMINATIONThis chapter describes “Normal Termination” and “Unexpected Termination”.8.1 Normal Termin

<8 TERMINATION>8-2IM 01R01A11-01EN8.2 Unexpected TerminationIf an unexpected termination occurs, follow this procedure.1) When an unexpec

<9 COMMUNICATION ERROR>9-1IM 01R01A11-01EN9 COMMUNICATION ERROR9.1 Error MessageThis chapter shows error dialogs. See Table 9.1.1 for det

Blank Page

<9 COMMUNICATION ERROR>9-2IM 01R01A11-01ENF090105.aiFigure 9.1.5 Error Dialog 5Table 9.1.1 Communication Error DialogFigure No.Message When

  <9COMMUNICATIONERROR>9-3IM 01R01A11-01EN9.2 DeviceAddressSettingWARNINGThis operation must be carried out by the trained personnel ha

Blank Page

IM 01R01A11-01ENRevision InformationAXF Verication ToolManual No.: IM 01R01A11-01EAug. 2012 / 1st Edition

Blank Page

<2 OUTILINE>2-1IM 01R01A11-01EN2 OUTILINEAXF Verication Tool is a PC application software running in conjunction with FieldMate R2.05.00