Yokogawa Integral Oxygen Analyzer ZR202 Manuel d'utilisateur télécharger pdf (Page 95)

IM 11M12A01-05E

7-22

7.10.2 Manual Calibration

The following describes how to perform a calibration.

7.10.2.1 Preliminary

Before performing a manual calibration, be sure that the ZA8F Flow Setting Unit zero-

gas flow valve is fully closed. Open the zero-gas cylinder pressure regulator so that the

secondary pressure equals measured gas plus approx. 50 kPa (or measured gas pressure

plus approx. 150 kPa when a check valve is used, maximum pressure rating is 300 kPa.).

1 2 ... 90 91 92 93 94 95 96 97 98 99 100 ... 180 181

User's 1
Introduction 2
(1) About This Manual 5
Contents 10
IM 1M12A01-05E 11
1. Overview 15
1.1.1 System 1 16
1.1.2 System 2 16
1.1.3 System 3 17
1.2.1 System Components 18
2. Specifications 19
2. Specifications 21
L= 0.4, 0.7 25
1.0, 1.5, 2.0 25
2.5, 3.0 (m) 25
Hood Material : Aluminum 27
Hood Weight : Approx. 800g 27
2.1.3 ZH21B Dust Protector 28
2.2.1 ZA8F Flow Setting Unit 29
ZR202G body 32
Autocalibration unit 32
2.3 ZO21S Standard Gas Unit 33
2.4 Other Equipment 34
Max. 210 36
3. Installation 41
3.1.2 Probe Insertion 42
Unit : mm 43
3.2.1 Location 44
4 - [6 hole, or M5 screw 45
3.3.1 Location 46
3. Installation 47
3.4.1 Location 48
3.4.2 Mounting 48
1. ANSI Class 150 2 RF 50
PIPING:A 52
F3.29E.EPS 56
F3.30E.EPS 56
4. Piping 57
Stop valve 58
Joint for tube 58
Calibration gas unit case 59
4. Piping 61
Unit: mm 62
5. Wiring 64
5.1.2 Wiring 65
5.1.3 Mounting of Cable Gland 66
4-G1/2, 1/2 NPT or the like 66
(Wiring connection) 66
5.2 Wiring for Analog Output 67
5.3.1 Wiring for Power Line 68
5.4 Wiring for Contact Output 69
5.5 Wiring for Contact Input 70
6. Components 72
Horizontal 73
Vertical 73
7. Startup 74
7.2 Valve Setup 75
7. Startup 78
7.4.5 Changing Set Values 81
7.6 Setting Display Item 84
7.7 Current Output Setting 85
7.7.2 Output Range Setting 86
7.8 Checking Current Loop 88
7.9 Checking Contact I/O 89
7.9.1 Contact Output Check 90
7.9.3 Checking Input Contacts 92
7.10 Calibration 93
7.10.2 Manual Calibration 95
8. Detailed Data Setting 98
8. Detailed Data Setting 100
IM 11M12A01-05E 101
8.1.4 Default Values 102
8.2 Output Hold Setting 103
T8.6E.EPS 105
8.3 Alarm Setting 106
8.3.3 Alarm Setting Procedure 108
8.3.4 Default Values 109
8.4 Output Contact Setup 110
8.4.2 Setting Output Contact 111
8.4.3 Default Values 112
8.5 Input Contact Settings 113
8.5.2 Default Values 114
Omitted here 115
T8.15E.EPS 116
8.6.4 Setting Purging 117
T8.17E.EPS 117
9. Calibration 118
Cell output, mV 119
E = -50.74*log PX/20.6 119
9.1.2 Calibration Gas 120
9.1.3 Compensation 121
9. Calibration 122
9.2 Calibration Procedures 123
10. Other Functions 128
Zero-gas ratio 4 % 129
10.1.1 Oxygen Concentration 130
10.1.2 Humidity 130
10.1.3 Mixing Ratio 130
10.1.4 Relative Humidity 130
10.1.5 Dew Point 130
10.1.12 Current Output 132
10.1.13 Response Time 132
5 One year min 133
3 Six months min 133
2 Three months min 133
1 One month max 133
00.06.21 134
10.3 Initialization Procedure 136
10.4 Reset 137
Table 10.6 Resetting 138
Table 10.7 Parameter Codes 139
T10.6E.EPS 143
F10.14E.EPS 146
10.5.3 Calibration Gas Flow 147
T10.6.3.EPS 151
Calibration gas tube 153
Exploded view of components 153
(with outside diameter 153
Groove in which the contact 155
(E7042BS) is placed 155
F11.3E.EPS 156
View A-A 157
11.1.4 Replacement of O-ring 158
11.2.1 Replacing Fuses 160
F11.5E.EPS 160
Cover of Display 160
Vertical mounting 162
Horizontal mounting 162
12. Troubleshooting 164
F12.2E.EPS 165
Multimeter 165
(V) 165
Heater wire 165
F12.3E.EPS 166
12.2.1 What is an Alarm? 167
Displayed alternately 167
F12.4E.EPS 167
12. Troubleshooting 168
1% 67.1 168
Customer 176
Maintenance 176
Parts List 176
CMPL 11M12A01-05E 177
Revision Record 180
IM 11M12A01-05E 181

Commentaires sur ces manuels

Pas de commentaire

Yokogawa Integral Oxygen Analyzer ZR202 Manuel d'utilisateur Page 95

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement aérien Yokogawa Integral Oxygen Analyzer ZR202