Yokogawa DAQWORX Manuel d'utilisateur Page 158
- Page / 163
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-4
IM WX103-01E
The measured value is not correct.
Probable Cause Corrective Action Reference Page
The input wiring is not correct. Check the input wiring. *
The measured value is at +Over or –Over.
The measurement range setting and input
range do not match.
Change to an appropriate setting. *
The temperature error is large or is
unstable. The TC type setting and the type
actually connected are different.
Change to the correct setting. *
The temperature error is large or is
unstable.
The RJC setting is not correct.
Change to the correct setting. *
The temperature error is large or is
unstable.
The wind is hitting the terminals.
Block the wind from hitting the terminals. -
The temperature error is large or is
unstable.
The ambient temperature change is
drastic.
Suppress changes in the ambient temperature such as by
placing the MX100 in a box.
-
The temperature error is large or is
unstable.
There is an error in the wiring resistance
(in the case of an RTD).
Match the thickness and length of the three wires. *
The measurement error is large or is
unstable.
Noise effects.
Take measures against noise. *
The measurement error is large or is
unstable.
Effects from the signal source resistance.
Reduce the signal source resistance such as by inserting a
converter.
-
The temperature error is large or is
unstable.
Effects from parallel connections.
Stop parallel connections.
Do not use the burnout setting.
-
Measured value from strain gauge type
sensor not correct.
When using a sensor without a remote sensing wire,
use the DV450-001 (conversion cable).
*
On the strain module (-B12, -B35), the
gauge method dipswitch settings is not
correct.
Enter the correct settings. *
On the strain module (-B12, -B35), the
gauge resistance and internal bridge
resistance values are different.
Use a module that supports the resistance value of the strain
gauge (For 120Ω, -B12, and for 350Ω, -B35.)
*
On the strain module, scaling
corresponding to the gauge method is
not set. (for 2 gauge, 4 gauge methods,
the amount of strain is doubled or
quadrupled.)
Displayed with 1 gauge method conversion. Depending on the
gauge method, set scaling appropriately.
*
On the strain module (-NDI), a strain
gauge type sensor without a remote
sensing wire is being used.
When using a sensor without a remote sensing wire, use the
DV450-001 (conversion cable).
*
* See the MX100 User’s Manual (IM MX100-01E).
5.1 Troubleshooting
- MXLOGGER 1
- Trademarks 2
- Revisions 2
- Software License Agreement 3
- Contents 5
- Chapter 3 Viewer 7
- Chapter 4 Calibrator 7
- Chapter 5 Troubleshooting 7
- Functional Overview 8
- Calibrator 10
- 1.2 MXLOGGER Operation Guide 11
- Overview of Operations 12
- Configure the system 13
- For details, see 13
- Click here to hide the Record 14
- Event settings window 18
- • Alarm Monitor 19
- • Trend Monitor 20
- • Numeric Monitor 20
- • Meter Monitor 21
- • All Channel Monitor 21
- Record the data 23
- 1.3 PC System Requirements 27
- Printer and Mouse 28
- Sound Board 28
- Ethernet Port 28
- 1.4 Setting Up MXLOGGER 29
- Configuring the Network 31
- Setting Up the Network 32
- Subnet Mask 34
- Default Gateway 34
- Connected User (User) 34
- Software 34
- 2.2 Configuring the System 35
- Auto Assignment 37
- MX100 Response Check 38
- CF Card Information 39
- Data Acquisition Conditions 40
- Setting the Data File 41
- Automatic Start Function 42
- Record Stop Condition 44
- Mode Is Set to STR) 47
- Setting the Measurement Span 51
- Setting the Scale 51
- Mode Is Set to RRJC (TC)) 51
- Setting the Burnout 52
- Setting the RJC 52
- 2.5 Setting Computations 54
- Importing Expressions 56
- Channels) 59
- Operators 59
- Arithmetic Functions 61
- Time Functions 62
- • Parameter Setting Ranges 62
- • Timer (<timerNo>) 63
- Timer Level Operation 63
- Manual AO Function 63
- Event Functions 64
- Notes on Computation 65
- 2.6 Setting Alarms 67
- Alarm Hysteresis 69
- 2.7 Digital Output 70
- Setting Analog Output 73
- Setting PWM Output 74
- Editing Pattern Output 75
- Deleting Points 76
- Fixed Output 77
- Rectangular Waveform Output 78
- Trapezoidal Waveform Output 78
- Pyramidal Waveform Output 79
- 2.9 Event Processing 82
- Setting Up Data File Events 83
- Setting Communication Events 84
- Setting Start Record Events 85
- Setting Stop Record Events 86
- Setting Up FTP and E-mail 87
- Configuring FTP 88
- Configuring E-Mail 88
- User File Settings 88
- Enabling/Disabling Events 89
- Displaying the Monitor 90
- Click here 93
- Y-Axis Type 98
- Scale Values 98
- Trip Points 100
- Channel Colors 100
- Clipping of Waveforms 100
- Adding Marks 101
- Grid Density 101
- Cursors 102
- Explanation 103
- Starting the Recording 104
- Stopping the Recording 104
- (Project) 106
- Printing Setup Data 107
- Print Preview 107
- Setting Up the Printer 107
- Changing the Port Number 109
- Procedure 111
- Description 112
- Information 113
- 3.1 Loading Data Files 114
- Synchronization 116
- Joining of Divided Files 117
- CF File Joining Function 118
- 3.2 Setting the Display 119
- IM WX103-01E 120
- Y-Axis Values 122
- Showing/Hiding Alarms 126
- Alarm/Mark List Display 127
- Numeric Display 129
- Settings Window 130
- Clearing Cursors 132
- Measured/Computed Data 133
- 3.5 Saving Display Settings 135
- Saving Templates 136
- Using Templates 136
- 3.7 Converting Data Formats 137
- Conversion Range and Step 138
- Specifying Formats 138
- Notes When Converting Data 138
- 3.8 Printing Data 139
- Executing the Print Operation 140
- Print Example 142
- 4.2 Calibration Procedure 147
- Start calibration 151
- 5.1 Troubleshooting 155
- Troubleshooting 157
- Error Messages on the Logger 159
- Error Messages on the Viewer 160
Produits connexes et manuels pour Logiciel Yokogawa DAQWORX
Logiciel Yokogawa DAQWORX Manuel d'utilisateur
(210 pages)
(210 pages)
Logiciel Yokogawa DAQWORX Manuel d'utilisateur
(100 pages)
(100 pages)
Keurig B50 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour la préparation du café Keurig B50.
Nous fournissons des manuels en pdf 1 Keurig B50 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels